2013-2015 Land Cruiser Prado · Service Manual Drivetrain

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "5" (S5 range) using the transmission control switch.
Shifting to "+" once raises the shift range by one, and shifting to "-" once lowers the shift range by one.

WIRING DIAGRAM

C179318E08

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION CONTROL SWITCH

  1. C203344E16
    Disconnect the G47 transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in S, "+" or "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in S, "+" or "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in S
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in S
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

  1. C203343E20
    Disconnect the G47 transmission control switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G47-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    G47-3 (IG) - Body ground
    Ignition switch off
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G47-5 (E) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Transmission Control Switch)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)

  1. C212049E05
    Disconnect the G70 TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G70-15 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    G70-15 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G70-22 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    G70-23 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    G70-22 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    G70-23 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to TCM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← U0100 Lost Communication with ECM / PCM "A" (from Aug 2014)Transmission Control Switch Circuit (from Aug 2014) →