2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Air Conditioning Signal Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

When the A/C compressor is on, the A/C amplifier sends the A/C signal to the ECM and the ECM increases the fuel injection volume to improve driveability during engine idling.

WIRING DIAGRAM

A227852E03

INSPECTION PROCEDURE


When using intelligent tester:


1. READ VALUE USING INTELLIGENT TESTER (AIR CONDITIONING SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the A/C switch on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/C SIG.

    Result:
    Switch Condition
    A/C SIG
    A/C switch off
    OFF
    A/C switch on
    ON



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK ECM (AC1 VOLTAGE)

  1. A062416E99
    Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G62-2 (AC1) - Body ground
    A/C switch on
    Below 1.5 V
    G62-2 (AC1) - Body ground
    A/C switch off
    7.5 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 3
OK

REPLACE ECM (Click here)

3. CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the A/C amplifier connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G25-17 (AC1) - G62-2 (AC1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G25-17 (AC1) or G62-2 (AC1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A/C amplifier connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


When not using intelligent tester:


1. CHECK ECM (AC1 VOLTAGE)

  1. A062416E99
    Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G62-2 (AC1) - Body ground
    A/C switch on
    Below 1.5 V
    G62-2 (AC1) - Body ground
    A/C switch off
    7.5 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONING AMPLIFIER)
  1. Disconnect the A/C amplifier connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    G25-17 (AC1) - G62-2 (AC1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    G25-17 (AC1) or G62-2 (AC1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the A/C amplifier connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← Starter Signal Circuit (from Aug 2014)Air Conditioning Signal Circuit (from Aug 2014) →