B2274 ACC Monitor Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when there is a problem in the ACC output circuit, which is from the ACC output terminal of the power management control ECU to the ACC relay.- HINT:
- When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2274 |
The ACC relay actuation circuit inside the power management control ECU or other related circuit is malfunctioning. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
- Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
| 1. CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU) |
Disconnect the G51 power management control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G51-2 (AM21) - Body ground
Always
9.5 to 14 V
G51-1 (AM22) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND) |
Disconnect the G51 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-6 (GND) - Body ground
Always
Below 1 Ω
G51-5 (GND2) - Body ground
Text in Illustration *a
Rear view of wire harness connector
(to Power Management Control ECU)
|
|
||||
| OK | |
| 3. INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY) |
Remove the driver side junction block assembly.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2A-48 - 2D-4
20°C (68°F)
101.25 to 123.75 Ω
Text in Illustration *a
Component without harness connected
(Driver Side Junction Block Assembly)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY) |
Disconnect the G51 power management control ECU connector.
Disconnect the 2A driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G51-19 (ACCD) - 2A-48
Always
Below 1 Ω
G51-19 (ACCD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
Disconnect the 2D driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-4 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK POWER MANAGEMENT CONTROL ECU |
Connect the power management control ECU connector.


Text in Illustration *a
Component with harness connected
(Power Management Control ECU)
-
-
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G51-19 (ACCD) - Body ground
Engine switch off
Below 1 V
Engine switch on (ACC)
((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
|
|
||||
| OK | ||
| ||
