DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn ON the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
*: Electronically Controlled BrakeABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light/ ON or OFF
OFF
-
Brake Warning Light
Brake warning light/ ON or OFF
OFF
-
Buzzer
Buzzer/ ON or OFF
ON: Buzzer on
OFF: Buzzer off
The combination meter has a built-in buzzer.
Stop Light SW
Stop light switch/ ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch/ ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW
Main idle switch/ ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch/ ON or OFF
ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-
Gear Position
Gear position information/ "P,N", R, 1st-8th, Fail or Not R
Actual gear position
-
Shift Lever Position
Shift lever position information/ "P,N", R, D/M, 1st-6th/B, Fail
-
The actual shift lever position.
Shift information
Shift information/ ON or OFF
ON: During gear change
OFF: Not during gear change
-
Inspection Mode
Inspection mode/ Other or Inspect
Other: Normal mode
Inspect: Inspection mode
-
Number of IG ON(Inspection)
Number of times ignition switch turned to ON after entering inspection mode/ Min.: 0, Max.: 255
-
-
Master Cylinder Sensor
Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
When brake pedal is released: 0.3 to 0.9 V
The value increases when the brake pedal is depressed.
Zero Point of M/C
Memorized zero value/ Min.: -12.50 Mpa, Max.: 12.40 Mpa
After master cylinder pressure sensor zero point calibration: 2.45 +/- 1 Mpa
-
Deceleration Sensor
Acceleration sensor/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Zero Point of Decele
Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
-
Deceleration Sensor2
Acceleration sensor 2/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Zero Point of Decele2
Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
-
Yaw Rate Sensor
Yaw rate sensor/ Min.: -128°/s, Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate
Memorized zero value/ Min.: -128°, Max.: 127°
After yaw rate sensor zero point calibration: 0°
-
Yaw Rate Sensor2
Yaw rate sensor 2/ Min.: -128°/s, Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate2
Memorized zero value/ Min.: -128°/s, Max.: 127°/s
After yaw rate sensor zero point calibration: 0°/s
-
Steering Angle Sensor
Steering angle sensor/ Min.: -3276.8°, Max.: 3276.7°
Left turn: Increase
Right turn: Decrease
-
Zero Point of Steering Angle
Memorized zero value/ Min.: -3276.8°, Max.: 3276.7°
After steering angle sensor zero point calibration: 0°
-
Lateral G
Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during turning.
Forward and Rearward G
Forward and backward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion to acceleration during acceleration/deceleration.
Yaw Rate Value
Yaw rate value/ Min.: -128°/s, Max.: 127°/s
-
Changes in proportion to yaw during turning.
Steering Angle Value
Steering angle value/ Min.: -3276.8°, Max.: 3276.7°
-
Changes in proportion to the amount of steering wheel rotation during steering operation.
Slip Indicator Light
Slip indicator light/ ON or OFF
ON: Indicator light ON
OFF: Indicator light OFF
-
L4 Switch
Transfer L4 detection switch/ ON or OFF
ON: Transfer L4 position
OFF: Transfer except L4 position
-
FR Wheel Speed
FR wheel speed sensor value/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped:
0 km/h
No large fluctuations when driving at a constant speed.
FL Wheel Speed
FL wheel speed sensor value/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped:
0 km/h
No large fluctuations when driving at a constant speed.
RR Wheel Speed
RR wheel speed sensor value/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped:
0 km/h
No large fluctuations when driving at a constant speed.
RL Wheel Speed
RL wheel speed sensor value/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped:
0 km/h
No large fluctuations when driving at a constant speed.
Vehicle Speed
Maximum wheel speed sensor value/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped:
0 km/h
No large fluctuations when driving at a constant speed.
FR Wheel Acceleration
FR wheel acceleration/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FL Wheel Acceleration
FL wheel acceleration/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RR Wheel Acceleration
RR wheel acceleration/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RL Wheel Acceleration
RL wheel acceleration/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FR Wheel Direction
Front wheel RH direction signal/ Forward or Back
Forward: Forward
Back: Backward
-
FL Wheel Direction
Front wheel LH direction signal/ Forward or Back
Forward: Forward
Back: Backward
-
RR Wheel Direction
Rear wheel RH direction signal/ Forward or Back
Forward: Forward
Back: Backward
-
RL Wheel Direction
Rear wheel LH direction signal/ Forward or Back
Forward: Forward
Back: Backward
-
EBS Relay
Stop light control ECU (Emergency brake signal)/ ON or OFF
ON: Stop light control ECU on
OFF: Stop light control ECU off
-
FR Wheel ABS Ctrl Status
FR wheel ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status
FL wheel ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status
RR wheel ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status
RL wheel ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel EBD Ctrl Status
RR wheel EBD control status/ ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel EBD Ctrl Status
RL wheel EBD control status/ ON or OFF
ON: During control
OFF: Not during control
-
BA Ctrl Status
BA control status/ ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Ctrl Status
TRC control status/ ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Engine Ctrl Status
TRC engine control status/ ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Brake Ctrl Status
TRC brake control status/ ON or OFF
ON: During control
OFF: Not during control
-
FR Wheel VSC Ctrl Status
FR wheel VSC control status/ ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel VSC Ctrl Status
FL wheel VSC control status/ ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel VSC Ctrl Status
RR wheel VSC control status/ ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel VSC Ctrl Status
RL wheel VSC control status/ ON or OFF
ON: During control
OFF: Not during control
-
Engine Revolutions
Engine speed/ Min.: 0 rpm, Max.: 65535 rpm
Engine stopped:
0 rpm
-
Real Engine Torque
Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Percentage of accelerator pedal opening angle/ Min.: 0.0%, Max.: 128.0%
When accelerator pedal released: 0%
Changes in proportion to the movement of the pedal during accelerator pedal operation.
Solenoid Relay
ABS solenoid relay/ ON or OFF
ON: Solenoid relay ON
OFF: Solenoid relay OFF
-
ECB* Motor Relay
Motor relay/ ON or OFF
ON: Motor relay ON
OFF: Motor relay OFF
-
Fail Safe Motor Relay
Motor fail-safe relay/ ON or OFF
ON: Motor relay ON
OFF: Motor relay OFF
-
TR(A)C/VSC Solenoid (SM2)
Master cut solenoid (SM2)/ ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SM1)
Master cut solenoid (SM1)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH)
ABS solenoid (SFRH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR)
ABS solenoid (SFRR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH)
ABS solenoid (SFLH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR)
ABS solenoid (SFLR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH)
ABS solenoid (SRRH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR)
ABS solenoid (SRRR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH)
ABS solenoid (SRLH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR)
ABS solenoid (SRLR)/ ON or OFF
ON: Operating
OFF: Not operating
-
FR Speed Open
Front speed sensor RH open circuit detection/ Error or Normal
Normal
-
FL Speed Open
Front speed sensor LH open circuit detection/ Error or Normal
Normal
-
RR Speed Open
Rear speed sensor RH open circuit detection/ Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open circuit detection/ Error or Normal
Normal
-
EFI Communication Open
EFI communication open circuit detection/ Error or Normal
Normal
-
Yaw Rate Open
Yaw rate sensor open circuit detection/ Error or Normal
Normal
-
Deceleration Open
Acceleration sensor open circuit detection/ Error or Normal
Normal
-
Steering Open
Steering angle sensor open circuit detection/ Error or Normal
Normal
-
Master Cylinder Open
Master cylinder pressure sensor open circuit detection/ Error or Normal
Normal
-
Wheelbase Information
Wheelbase information/ Short, Long, Without
Short: Short wheelbase
Long: Long wheelbase
-
IG1 Voltage Value
IG1 voltage/ Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
-
MT Voltage Value
Motor driving monitor voltage/ Min.: 0.00 V, Max.: 20.00 V
-
-
TRC/VSC Off Mode
TRC/VSC off mode/ Normal, TRC OFF, VSC OFF or Unknown
Normal: Normal mode
TRC OFF: TRC OFF mode
VSC OFF: TRC, VSC OFF mode
-
Number of DTC
Number of DTCs stored/ Min.: 0, Max.: 255
0
-
IG Voltage Value Decreased
IG voltage value decrease detection/ Error or Normal
Normal
-
IG Voltage Value Increased
IG voltage value increase detection/ Error or Normal
Normal
-
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open circuit detection/ Error or Normal
Normal
-
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open circuit detection/ Error or Normal
Normal
-
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open circuit detection/ Error or Normal
Normal
-
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open circuit detection/ Error or Normal
Normal
-
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection/ Error or Normal
Normal
-
Brake Pedal Switch Open
Brake pedal load sensing switch open circuit detection/ Error or Normal
Normal
-
Yaw Rate Sensor Voltage Open
Yaw rate sensor voltage open circuit detection/ Error or Normal
Normal
-
EFI Communication Invalid
EFI communication invalid detection/ Error or Normal
Normal
-
Hazard Switch History
Hazard warning switch history/ Incomplete or Complete
Normal
-
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn ON the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe the combination meter.
Brake Warning Light
Brake warning light
Warning light ON/OFF
Observe the combination meter.
Buzzer
Buzzer
Buzzer ON/OFF
The buzzer can be heard.
Solenoid Relay
Solenoid relay
Relay ON/OFF
-
Motor Relay
Motor relay
Relay ON/OFF
The operating sound of the motor can be heard.
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMR)
Master cut solenoid (SM2)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SMF)
Master cut solenoid (SM1)
Solenoid ON/OFF
The operating sound of the solenoid (clicking sound) can be heard.
TRC(TRAC) OFF Indicator Light
TRC OFF indicator light
Indicator light ON/OFF
Observe the combination meter.
VSC OFF Indicator Light
VSC OFF indicator light
Indicator light ON/OFF
Observe the combination meter.
Slip Indicator Light
Slip indicator light
Indicator light ON/OFF
Observe the combination meter.
EBS Relay
Stop light control ECU (Emergency brake signal)
Stop light control ECU ON/OFF
Make sure the hazard warning switch is off and the stop light switch is on when performing this Active Test.
ABS Solenoid
Selection of multiple ABS solenoids (SFRH, SFLH, SRRH, SRLH, SFRR, SFLR, SRRR and SRLR) possible
Start/Stop
Start: When Start is selected, the selected solenoids turn ON.
Stop: When Stop is selected, the selected solenoids turn OFF.
VSC/TRC(TRAC) Solenoid
Selection of master cut solenoids SMR (SM2) and SMF (SM1) possible
Start/Stop
Start: When Start is selected, the selected solenoids turn ON.
Stop: When Stop is selected, the selected solenoids turn OFF.