2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK CERTIFICATION ECU
B203498E30
  1. Disconnect the G38 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G38-1 (+B) - G38-15 (E)
    V - W-B
    +B power supply
    Always
    11 to 14 V
    G38-15 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G38-16 (IG) - G38-15 (E)
    W - W-B
    IG power supply
    Engine switch off → on (IG)
    Below 1 V →11 to 14 V
    G38-17 (CUTB) - G38-15 (E)
    L - W-B
    +B power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the G38 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G38-3 (CLG1) - G38-15 (E)
    R - W-B
    Electrical key antenna (for driver side) sensor signal
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    G38-4 (CG1B) - G38-15 (E)
    G - W-B
    Electrical key antenna (for driver side) sensor signal
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    G38-5 (CLG2) - G38-15 (E)
    B - W-B
    Electrical key antenna (for front passenger side) sensor signal
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    G38-6 (CG2B) - G38-15 (E)
    W - W-B
    Electrical key antenna (for front passenger side) sensor signal
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    G38-7 (CLG5) - G38-15 (E)
    R - W-B
    Indoor No. 1 electrical key antenna (front floor) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-8 (CG5B) - G38-15 (E)
    W - W-B
    Indoor No. 1 electrical key antenna (front floor) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-18 (TSW1) - G38-15 (E)
    LG - W-B
    Entry lock sensor (for driver side) detection signal
    Engine switch off, all doors closed and lock sensor (for driver side) off → on
    Pulse generation → Below 2 V
    G38-19 (TSW2) - G38-15 (E)
    V - W-B
    Entry lock sensor (for front passenger side) detection signal
    Engine switch off, all doors closed and lock sensor (for front passenger side) off → on
    Pulse generation → Below 2 V
    G38-20 (SEN1) - G38-15 (E)
    W - W-B
    Entry unlock sensor (for driver side) detection signal
    Engine switch off, all doors locked, key not sufficiently close to vehicle and unlock sensor (for driver side) off → on
    Pulse generation → Below 2 V
    G38-21 (SEN2) - G38-15 (E)
    L - W-B
    Entry unlock sensor (for front passenger side) detection signal
    Engine switch off, all doors locked, key not sufficiently close to vehicle and unlock sensor (for front passenger side) off → on
    Pulse generation → Below 2 V
    G38-22 (TSW5) - Body ground
    G - Body ground
    Luggage electrical key switch signal
    Unlock switch off → on
    Pulse generation → Below 1 V
    G38-23 (TSW6) - Body ground
    L - Body ground
    Luggage electrical key switch signal
    Lock switch off → on
    Pulse generation → Below 1 V
    G38-24 (CLG6) - G38-15 (E)
    Y - W-B
    Indoor No. 2 electrical key antenna (rear floor) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-25 (CG6B) - G38-15 (E)
    W - W-B
    Indoor No. 2 electrical key antenna (rear floor) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-26 (CLG7) - G38-15 (E)
    LG - W-B
    Indoor No. 3 electrical key antenna (inside luggage) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-27 (CG7B) - G38-15 (E)
    L - W-B
    Indoor No. 3 electrical key antenna (inside luggage) sensor signal
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-32 (POS1) - G38-15 (E)
    R - W-B
    Entry unlock sensor (for driver side) output signal
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V
    G38-33 (POS2) - G38-15 (E)
    R - W-B
    Entry unlock sensor (for front passenger side) output signal
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V
    G39-5 (RCO) - G38-15 (E)
    L - W-B
    Door control receiver power source
    Engine switch off and transmitter switch not pressed → pressed
    Below 1 V → 4.5 to 5.5 V
    G39-15 (RDA) - G38-15 (E)
    G - W-B
    Door control receiver data input signal
    Engine switch off
    11 to 14 V pulse generation at regular intervals
    G39-16 (RSSI) - G38-15 (E)
    P - W-B
    Door control receiver electric wave existence signal
    All doors closed, all doors locked and transmitter switch not pressed → pressed
    11 to 14 V → Below 2 V
    G39-19 (CLG8) - G38-15 (E)
    B - W-B
    Electrical key antenna (outside luggage) sensor signal
    Engine switch off, all doors closed and unlock switch off → on
    No pulse generation → Pulse generation
    G39-20 (CG8B) - G38-15 (E)
    W - W-B
    Electrical key antenna (outside luggage) sensor signal
    Engine switch off, all doors closed and unlock switch off → on
    No pulse generation → Pulse generation
    If the result is not as specified, the certification ECU may have a malfunction.


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
B235899E06
Text in Illustration 
*A
for LHD
*B
for RHD
  1. Remove the main body ECU (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Auxiliary battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Engine switch power supply
    Engine switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    G63-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2I-27 (FLCY) - Body ground*1
    R - Body ground
    Front door LH courtesy switch input
    Front door LH open
    Below 1 V
    2I-27 (FLCY) - Body ground*1
    R - Body ground
    Front door LH courtesy switch input
    Front door LH closed
    11 to 14 V
    2D-31 (FLCY) - Body ground*2
    R - Body ground
    Front door LH courtesy switch input
    Front door LH open
    Below 1 V
    2D-31 (FLCY) - Body ground*2
    R - Body ground
    Front door LH courtesy switch input
    Front door LH closed
    11 to 14 V
    2D-15 (FRCY) - Body ground*1
    B - Body ground
    Front door RH courtesy switch input
    Front door RH open
    Below 1 V
    2D-15 (FRCY) - Body ground*1
    B - Body ground
    Front door RH courtesy switch input
    Front door RH closed
    11 to 14 V
    2H-26 (FRCY) - Body ground*2
    B - Body ground
    Front door RH courtesy switch input
    Front door RH open
    Below 1 V
    2H-26 (FRCY) - Body ground*2
    B - Body ground
    Front door RH courtesy switch input
    Front door RH closed
    11 to 14 V
    G65-3 (LCTY) - Body ground*3
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    G65-3 (LCTY) - Body ground*3
    V - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    11 to 14 V
    G64-6 (RCTY) - Body ground*3
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    G64-6 (RCTY) - Body ground*3
    R - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    11 to 14 V
    G64-19 (BCTY) - Body ground
    G - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    G64-19 (BCTY) - Body ground
    G - Body ground
    Back door courtesy light switch input
    Engine switch off, all doors closed and back door closed
    Pulse generation (see waveform 1 or 2)
    G64-1 (GCTY) - Body ground*4
    V - Body ground
    Glass hatch courtesy switch input
    Glass hatch open
    Below 1 V
    G64-1 (GCTY) - Body ground*4
    V - Body ground
    Glass hatch courtesy switch input
    Engine switch off, all doors closed and glass hatch closed
    Pulse generation (see waveform 3 or 4)
    G64-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Front door LH unlocked
    Below 1 V
    G64-7 (LSFL) - Body ground
    G - Body ground
    Front door LH lock position switch input
    Engine switch off, all doors closed and front door LH locked
    Pulse generation (see waveform 5 or 6)
    G64-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Front door RH unlocked
    Below 1 V
    G64-18 (LSFR) - Body ground
    G - Body ground
    Front door RH lock position switch input
    Engine switch off, all doors closed and front door RH locked
    Pulse generation (see waveform 7 or 8)
    2I-25 (LSWL) - Body ground*1, *3
    B - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2I-25 (LSWL) - Body ground*1, *3
    B - Body ground
    Rear door LH lock position switch input
    Engine switch off, all doors closed and rear door LH locked
    Pulse generation (see waveform 9 or 10)
    2D-16 (LSWL) - Body ground*2, *3
    B - Body ground
    Rear door LH lock position switch input
    Rear door LH unlocked
    Below 1 V
    2D-16 (LSWL) - Body ground*2, *3
    B - Body ground
    Rear door LH lock position switch input
    Engine switch off, all doors closed and rear door LH locked
    Pulse generation (see waveform 11 or 12)
    G63-2 (LSWR) - Body ground*3
    V - Body ground
    Rear door RH lock position switch input
    Rear door RH unlocked
    Below 1 V
    G63-2 (LSWR) - Body ground*3
    V - Body ground
    Rear door RH lock position switch input
    Engine switch off, all doors closed and rear door RH locked
    Pulse generation (see waveform 13 or 14)
    G65-13 (LSWB) - Body ground
    SB - Body ground
    Back door lock position switch input
    Back door lock unlocked
    Below 1 V
    G65-13 (LSWB) - Body ground
    SB - Body ground
    Back door lock position switch input
    Engine switch off, all doors closed and back door locked
    Pulse generation (see waveform 15 or 16)
    1. *1: for LHD
    2. *2: for RHD
    3. *3: for 5 Door
    4. *4: w/ Glass Hatch Opener System
    If the result is not as specified, the main body ECU or driver side junction block assembly may have a malfunction.

  5. B199631E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-19 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door closed

  6. B199632E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-19 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door closed

  7. B199631E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-1 (GCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and glass hatch closed

  8. B199632E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-1 (GCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and glass hatch closed

  9. B199631E01
    Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and front door LH locked

  10. B199632E01
    Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and front door LH locked

  11. B199631E01
    Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and front door RH locked

  12. B199632E01
    Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and front door RH locked

  13. B199631E01
    Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    2I-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH locked

  14. B199632E01
    Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    2I-25 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH locked

  15. B199631E01
    Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    2D-16 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH locked

  16. B199632E01
    Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    2D-16 (LSWL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door LH locked

  17. B201885E01
    Using an oscilloscope, check waveform 13.
    Waveform 13 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G63-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door RH locked

  18. B201886E01
    Using an oscilloscope, check waveform 14.
    Waveform 14 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G63-2 (LSWR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and rear door RH locked

  19. B199631E01
    Using an oscilloscope, check waveform 15.
    Waveform 15 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G65-13 (LSWB) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door locked

  20. B199632E01
    Using an oscilloscope, check waveform 16.
    Waveform 16 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G65-13 (LSWB) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, all doors closed and back door locked

← TERMINALS OF ECU (Aug 2013 – Jul 2014)DTC CHECK / CLEAR (from Aug 2013) →