2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE RADIATOR GRILLE

B357908E01
  1. Put protective tape around the radiator grille.

  1. Remove the 4 screws.

  1. Detach the 8 claws and remove the radiator grille.

    Text in Illustration 
    *1
    Protective Tape


3. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

B348963
  1. Disconnect the sensor connector.

  1. Remove the 3 bolts and millimeter wave radar sensor assembly.


4. REMOVE HOOD LOCK RELEASE LEVER PROTECTOR

  1. B243267
    Detach the 2 clamps and 2 guides and remove the hood lock release lever protector.


5. REMOVE LOW PITCHED HORN ASSEMBLY (for LHD)

B237907E01
  1. Disconnect the connector.

    Text in Illustration 
    *1
    Connector

  1. Remove the bolt and low pitched horn.


6. REMOVE HIGH PITCHED HORN ASSEMBLY (for LHD)

B237908E01
  1. Disconnect the connector.

    Text in Illustration 
    *1
    Connector

  1. Remove the bolt and high pitched horn.


7. REMOVE HOOD LOCK CONTROL CABLE COVER

  1. B241650E03
    Remove the 2 screws.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. Detach the claw and remove the hood lock control cable cover.


8. REMOVE HOOD LOCK ASSEMBLY (for LHD)

  1. B238477
    Remove the 3 bolts.

  1. w/ Engine Hood Courtesy Switch:

    1. B238478E01
      Disconnect the connector.
      Text in Illustration 
      *A
      w/ Engine Hood Courtesy Switch

  1. Disconnect the hood lock control cable and remove the hood lock assembly.


9. REMOVE HOOD LOCK ASSEMBLY (for RHD)

  1. B238479
    Remove the 3 bolts.

  1. w/ Engine Hood Courtesy Switch:

    1. B238480E01
      Disconnect the connector.
      Text in Illustration 
      *A
      w/ Engine Hood Courtesy Switch

  1. Disconnect the hood lock control cable and remove the hood lock assembly.


10. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

  1. for LHD:

    1. B246473E01
      Detach the clamp as shown in the illustration.
      Text in Illustration 
      *1
      Protector
      *2
      Fuel Lid Lock Control Cable
      *3
      Hood Lock Control Cable
      *4
      Clamp

    2. B246507
      Detach the 3 claws.

    3. B238482
      Remove the hood lock control cable assembly and hood lock control lever sub-assembly.

  1. for RHD:

    1. B238481
      Detach the 3 claws.

    2. B238482
      Remove the hood lock control cable assembly and hood lock control lever sub-assembly.


11. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)
  1. Using a screwdriver, detach the clamps shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the hood lock control cable assembly from the engine compartment and remove it.

    B238485E01

    Text in Illustration 
    *A
    for Engine Room Side
    -
    -
    *1
    Hood Lock Control Cable
    *2
    Stopper


12. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)
  1. Using a screwdriver, detach the clamps shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the hood lock control cable assembly from the engine compartment and remove it.

    B238486E01

    Text in Illustration 
    *A
    for Engine Room Side
    -
    -
    *1
    Hood Lock Control Cable
    *2
    Stopper
    *3
    Rear Washer Hose
    -
    -

← COMPONENTS (from Aug 2013)INSTALLATION (from Aug 2013) →