2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT DOOR CONTROL TRANSMITTER MODULE (except Separate Type)

NOTICE:
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

  1. Inspect the operation of the transmitter.

    1. Remove the battery (lithium battery) from the transmitter (Click here).

    2. B185421
      Install a new or normal battery (lithium battery).

      HINT:
      When a new or normal battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the transmitter shown in the illustration.

    3. From outside the vehicle, approximately 1 m (3.28 ft) from the driver side outside door handle, test the transmitter by pointing its key plate at the vehicle and pressing a transmitter switch.

      OK:
      The door lock can be operated via the transmitter.
      The LED comes on more than once.

      1. The operational area differs depending on the user, the way the transmitter is held and the location.
      2. The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The transmitter operational area may be reduced or the transmitter may not function.

  1. Inspect the battery capacity.

    1. Remove the battery from the electrical key transmitter that does not operate (Click here).

    2. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    3. B178438
      Carefully extend the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    4. B359150E01
      Check the transmitter battery voltage.

      HINT:
      Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.

      Text in Illustration 
      *a
      GND

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Transmitter battery positive (+) - Transmitter battery negative (-)
      Ignition switch off, all doors closed and lock or unlock switch is pressed
      2.5 to 3.2 V

      If the result is not as specified, replace the transmitter battery.


INSPECT TRANSMITTER BATTERY (for Separate Type)

NOTICE:
When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

  1. Inspect the operation of the transmitter.

    1. Remove the battery (lithium battery) from the transmitter (Click here).

    2. B239793
      Install a new or normal battery (lithium battery).

      HINT:
      If a new or normal battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the transmitter shown in the illustration.

    3. From outside the vehicle, approximately 1 m (3.28 ft) away from the driver side outside door handle, test the transmitter by pointing its key plate at the vehicle and pressing a transmitter switch, or while carrying the transmitter, touch the inside of the handle and pull it.

      OK:
      The door lock can be operated via the transmitter.
      The LED comes on more than once.

      HINT:
      1. The operational area differs depending on the user, the way the transmitter is held and the location.
      2. The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The transmitter operational area may be reduced or the transmitter may not function.

  1. B239794
    Inspect the battery capacity.

    1. Remove the battery from the electrical key transmitter that does not operate (Click here).

    2. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    3. Carefully extend the lead wire from the position shown in the illustration and install the previously removed transmitter battery.

    4. B359151E01
      Check the transmitter battery voltage.

      HINT:
      Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.

      Text in Illustration 
      *a
      GND

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Transmitter battery positive (+) - Transmitter battery negative (-)
      Ignition switch off, all doors closed and lock or unlock switch is pressed
      2.5 to 3.2 V

      If the result is not as specified, replace the transmitter battery.

← REMOVAL (from Aug 2013)INSTALLATION (from Aug 2013) →