2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY IN PLACE

C216539

2. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY REAR

F001237E20
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Distance from center to runout measurement point:
    30 mm (1.18 in.)

    Maximum Runout:
    Item
    Specified Condition
    Vertical runout
    0.10 mm (0.00394 in.)
    Lateral runout
    0.10 mm (0.00394 in.)

    Text in Illustration 
    *a
    Vertical Runout
    *b
    Lateral Runout
    1. If the runout is more than the maximum, replace the companion flange.


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

C216538
  1. Using a dial indicator, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.00276 in.)

    1. If the runout is more than the maximum, replace the ring gear with a new one.


4. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C216537
  1. Using a dial indicator, check the backlash of the ring gear.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00787 in.)

    1. If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

      HINT:
      Perform the measurement at 3 or more positions around the circumference of the ring gear.


5. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

C003092E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard preload (at starting):
    0.88 to 1.98 N*m (9.0 to 20.2 kgf*cm, 7.8 to 17.5 in.*lbf)

    If necessary, disassemble and inspect the differential.


6. INSPECT TOTAL PRELOAD

C003092E01
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

  1. Using a torque wrench, measure the total preload.

    Standard total preload (at starting):
    Drive pinion preload plus 0.20 to 0.40 N*m (2.04 to 4.07 kgf*cm, 1.77 to 3.54 in.*lbf)

    If necessary, disassemble and inspect the differential.


7. REMOVE REAR DRIVE PINION NUT

F044346E01
  1. Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

    SST
    09930-00010  

  1. SA02349E03
    Use SST to hold the companion flange.
    SST
    09330-00021  

  1. Using a 30 mm socket wrench, remove the rear drive pinion nut.


8. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

B087869E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.


9. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

SA02348E02
  1. Using SST, remove the rear differential carrier oil seal from the differential carrier.

    SST
    09308-10010  


10. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

11. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (INNER)

Z000641E01
  1. Using SST, remove the rear drive pinion front tapered roller bearing (inner) from the drive pinion.

    SST
    09556-22010  


12. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING (OUTER)

13. REMOVE DIFFERENTIAL CASE ASSEMBLY

C216540E02
  1. Place matchmarks on the bearing cap and differential carrier.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 4 bolts and 2 differential bearing caps.

  1. C216541
    Using a screwdriver and hammer, remove the 2 plate washers.

    HINT:
    Measure the plate washer thickness and note it down.

  1. C216542
    Remove the rear differential case assembly from the differential carrier.

    HINT:
    Tag the 2 case bearing outer races so that they can be reinstalled in the correct locations.


14. REMOVE DIFFERENTIAL DRIVE PINION

  1. C030540
    Remove the drive pinion and bearing spacer from the differential carrier.


15. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

R010668E01
  1. Using SST and a press, press out the roller bearing (inner) from the drive pinion.

    SST
    09950-00020  

    NOTICE:
    Do not drop the drive pinion.

    HINT:
    If the drive pinion or ring gear is damaged, replace them as a set.


16. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

F044358E01
  1. Using SST, remove the roller bearing (outer) from the carrier.

    SST
    09308-00010  

  1. Using a brass bar and hammer, tap out the oil storage ring from the carrier.

    HINT:
    If the bearing is damaged during removal, replace it.


17. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C216543E01
  1. Using SST, tap out the rear tapered roller bearing (outer) from the carrier.

    SST
    09308-00010  

    HINT:
    If the bearing is damaged during removal, replace it.


18. REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

19. REMOVE DIFFERENTIAL RING GEAR

C216547E02
  1. Place matchmarks on the ring gear and differential case.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 12 ring gear set bolts.

  1. C014054E02
    Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


20. INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

C216544
  1. Install the rear differential case bearing to the differential case.

  1. Install the differential case to the differential carrier.

  1. Install the 2 bearing caps to the differential carrier with the 4 bolts.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }

  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.00276 in.)

  1. Remove the differential case.

  1. Remove the rear differential case bearing.


21. REMOVE REAR DIFFERENTIAL CASE BEARING

F040345E02
  1. Using SST, remove the 2 bearings from the differential case.

    SST
    09950-40011   (09953-04020, 09951-04010, 09952-04010, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00500, 09951-00650, 09952-06010)

    NOTICE:
    Do not remove a case bearing unless replacing the differential case.


22. DISASSEMBLE DIFFERENTIAL CASE

C216546E02
  1. Place matchmarks on the LH and RH cases.

    Text in Illustration 
    *a
    Matchmark

  1. Remove the 8 bolts.

    NOTICE:
    Loosen the bolts, diagonally opposite of each other, in pairs.

  1. ZK09094
    Using a plastic-faced hammer, separate the LH and RH cases.

  1. C090324E05
    Remove the parts shown in the illustration from the differential case.
    Text in Illustration 
    *1
    Side Gear
    *2
    Side Gear Thrust Washer
    *3
    Spider
    *4
    Pinion Gear
    *5
    Pinion Gear Thrust Washer

← REMOVAL (from Aug 2013)INSPECTION (from Aug 2013) →