2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

DTC CHECK / CLEAR

Troubleshooting · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK DTC (CHECK USING GTS)
  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

  5. Check for DTCs, and then write them down.

  6. Check the details of the DTC(s).


CLEAR DTC (CLEAR USING GTS)
  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

  5. Clear the DTCs.


START DIAGNOSTIC MODE

HINT:
  1. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  2. After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

  1. Start the engine.

  2. While pressing and holding the "CAR" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

  3. E286247E01
    Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


FAILURE DIAGNOSIS

  1. E286356
    The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.


SYSTEM CHECK

  1. E287742
    The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.


CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

HINT:
When "NCON" is displayed for all devices connected using the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (Click here).

  1. E287743E01
    System check mode screen description
    Screen Description 
    Display
    Content
    *a: Device Name List No. 1
    1. Device Name List No. 1 displays some of the devices that make up the navigation system.
    2. The names of the components from Device Name List No. 1 are shown in the following table.
    *b: Check Result
    Result codes for all devices are displayed.
    *c: Memory Clear
    1. Present and history DTCs and registered connected device names are cleared.
    2. Press the "Memory CLR" switch for 3 seconds.
    *d: Recheck
    1. A system check will be performed again after the memory is cleared.
    2. The "Recheck" switch will dim during a system check.
    *e: Device Name List No. 2
    1. Device Name List No. 2 displays some of the devices that make up the navigation system.
    2. The names of the components from Device Name List No. 2 are shown in the following table.
    *a: Device Name List No. 1 Description 
    Name
    Component
    Connection Method
    DA
    Radio and display receiver assembly
    -
    CAMERA-C
    Parking assist ECU*1
    Communication line for AVC-LAN
    Rr-TV
    Television display assembly*2
    Communication line for AVC-LAN
    DSP-AMP
    Stereo component amplifier assembly
    Communication line for AVC-LAN
    NAVI BOX
    Navigation ECU
    LVDS communication line
    1. *1: w/ Side Monitor System
    2. *2: w/ Rear Seat Entertainment System
    *b: Check Result Description 
    Result
    Meaning
    Action
    OK
    The device does not respond with a DTC.
    -
    DETAIL
    The device responds with a DTC.
    Look up the DTC in "Unit Check Mode".
    NCON
    The device was previously present, but does not respond in diagnostic mode.
    - Check power supply wire harness of the device.
    - Check the AVC-LAN of the device.
    NRES
    The device responds in diagnostic mode, but gives no DTC information.
    - Check power supply wire harness of the device.
    - Check the AVC-LAN of the device.
    *e: Device Name List No. 2 Description 
    Name
    Component
    Connection Method
    AUX/VTR
    No. 1 stereo jack adapter assembly
    Vehicle wire harness
    VTR/RR
    Video (video adapter) terminal
    Vehicle wire harness

  2. E276983E01
    Unit check mode screen description
    Screen Description 
    Display
    Content
    *a: Device name
    Target device
    *b: History DTC
    Diagnostic memory results and stored DTCs are displayed.
    *c: Current DTC
    DTCs output in the service check are displayed.
    *d: DTC
    DTC (Diagnostic Trouble Code)
    *e: Timestamp
    The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
    *f: Diagnosis clear switch
    Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)

    HINT:
    1. This screen is updated once per second.
    2. A maximum of 6 DTCs can be displayed for history and present DTCs.

  3. E288151
    Read the system check result.

    1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

      NOTICE:
      A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

      HINT:
      1. When all results are "OK", this means that no DTCs are output.
      2. When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

    2. Check the details of the DTC(s) (Click here).


DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

  1. E288152
    Clear DTCs

    1. Press the "Memory CLR" switch for 3 seconds.

    2. Confirm that the check results are cleared.

      HINT:
      1. To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.
      2. When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

  2. E288153
    Recheck

    1. Press the "Recheck" switch.

    2. E288154
      Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

      HINT:
      When the DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.


FINISH DIAGNOSTIC MODE
  1. Turn the engine switch off.

← DTC CHECK / CLEAR (Aug 2013 – Jul 2014)FREEZE FRAME DATA (from Aug 2013) →