2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B240614
    Detach the 2 clips and remove the front door lower frame bracket garnish LH.


3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B238520
    Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.


4. REMOVE ASSIST GRIP COVER LH

  1. B238521
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B238522
    Remove the 3 screws.

  1. Remove the 12 clips.

  1. B238523E01
    Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.
    Text in Illustration 
    *1
    Reference Boss

  1. Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.

  1. B238524
    Disconnect the 2 connectors.

  1. w/ Seat Position Memory System:

    1. B240206
      Disconnect the connectors.

  1. B238525
    Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

  1. B238526
    Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


7. REMOVE FRONT REFLEX REFLECTOR ASSEMBLY

  1. E198063
    Detach the 2 claws and remove the front reflex reflector assembly.


8. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

  1. E198049E01
    Disconnect the connector.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and remove the light.

    HINT:
    Tape the screwdriver tip before use.


9. REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

  1. E198050
    Disconnect the connector.

  1. Detach the clamp.

  1. Turn the light in the direction indicated by the arrow and remove it.


10. REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

B240207
  1. Remove the 2 screws and switch.


11. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

  1. B238528
    Remove the 3 screws and the multiplex network master switch assembly.


12. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

B193241
  1. Detach the 2 claws and remove the power window regulator switch assembly.


13. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B238529
    Remove the 8 screws and door assist grip assembly LH.

  1. B238527
    Remove the 2 screws.

  1. Detach the guide and 2 claws and remove the front door inside handle sub-assembly from the front door trim board sub-assembly.


14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  1. B239132
    Disconnect the speaker connector.

  1. Remove the 4 screws.

  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone of the speaker.


15. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

  1. B238362
    Disconnect the connector.

  1. Remove the bolt and side airbag sensor.


16. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B238530
    Remove the bolt.

  1. Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


17. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B231561
  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Detach the claw and remove the outer rear view mirror.


18. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B238531
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B238532E01
    Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


19. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B238533E01
    Disconnect the connector.

  1. Loosen the temporary bolt.

    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


20. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. Using a T25 "TORX" socket wrench, remove the 3 screws and the power window regulator motor.

    B238976E03

    Text in Illustration 
    *1
    Spring
    -
    -
    *a
    Range of Movement
    -
    -

    CAUTION:
    Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury. NOTICE: Be careful when removing the screws as the motor may fall and become damaged.


21. REMOVE FRONT DOOR GLASS RUN LH

  1. B238535
    Remove the front door glass run.


22. REMOVE REAR DOOR FRAME GARNISH LH

  1. B238558
    Detach the clip and remove the door frame garnish.


23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B238536
    Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.


24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

  1. B238537
    Remove the hole plug.

  1. B238538
    Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

  1. B238539
    Using a screwdriver, detach the claw and remove the front door outside handle cover.


26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

  1. B241166
    Remove the hole plug.

  1. B238540
    Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


27. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. w/ Entry and Start System:

    1. B238541
      Detach the 2 claws.

    2. Disconnect the connector.

  1. B238542
    Move the lever in the direction indicated by the arrow in the illustration.

  1. B238543
    Remove the front door outside handle assembly as shown in the illustration.


28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

  1. B238544
    Detach the 3 claws and remove the front door front outside handle pad.


29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

  1. B238545
    Detach the 2 claws and remove the front door rear outside handle pad.


30. REMOVE FRONT DOOR LOCK ASSEMBLY LH
  1. Disconnect the connector.

  1. B237872E01
    Using a T30 "TORX" wrench, remove the 3 screws.
    Text in Illustration 
    *A
    w/o Double Locking System
    *B
    w/ Double Locking System
    V100135
    Slide

  1. Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.

  1. Remove the front door lock open rod from the front door lock assembly.

  1. Remove the door lock wiring harness seal from the front door lock assembly.


31. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B238548
    Remove the front door lock remote control cable assembly.


32. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B238549
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B238550
    Remove the front door inside locking cable assembly.


33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. w/ Entry and Start System:

    1. B238551
      Disconnect the connector.

    2. Detach the clamp and remove the front door No. 2 wire.

  1. B238553
    Using a T30 "TORX" socket wrench, loosen the screw.

  1. Slide the front door outside handle frame sub-assembly to detach the door handle nut and claw of the front door outside handle frame sub-assembly, and then remove the front door outside handle frame sub-assembly.


34. REMOVE FRONT DOOR NO. 2 WIRE LH (w/ Entry and Start System)

  1. B238552
    Detach the 4 clamps and remove the front door No. 2 wire.


35. REMOVE FRONT DOOR LOCK OPEN ROD LH

  1. B238554E01
    Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


36. REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

  1. B238555E01
    Remove the 2 bolts.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Detach the 2 claws and remove the front door No. 2 stiffener cushion.


37. REMOVE FRONT DOOR CHECK ASSEMBLY LH

  1. B238556
    Remove the bolt, 2 nuts and front door check assembly.


38. REMOVE FRONT DOOR WEATHERSTRIP LH

  1. B238557
    Using a clip remover, detach the 21 clips and remove the front door weatherstrip.


39. REMOVE FRONT DOOR BELT MOULDING LH

B236327E01
  1. Put protective tape around the belt moulding.

  1. Detach the 6 claws and remove the front door belt moulding.

    Text in Illustration 
    *1
    Protective Tape


40. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

  1. B243888
    Remove the door window frame moulding clip.

  1. B243889E01
    Put protective tape around the front door rear window frame moulding.

  1. Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.

    Text in Illustration 
    *1
    Protective Tape
    *2
    Double-sided Tape
    *3
    Moulding Remover


41. REMOVE NO. 1 BLACK OUT TAPE LH

B236330
  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.


42. REMOVE FRONT DOOR OUTSIDE STRIPE LH

B236332
  1. Pull back an edge of the front door outside stripe and pull it parallel to the vehicle body to remove it.


43. REMOVE LOWER FRONT DOOR OUTSIDE STRIPE LH

B236334
  1. Pull back an edge of the lower front door outside stripe and pull it parallel to the vehicle body to remove it.


44. REMOVE FRONT DOOR PANEL CUSHION

  1. B240615
    Using a clip remover, detach the clip and remove the door panel cushion.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2014) →