2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B239600
    Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.


3. REMOVE ASSIST GRIP COVER LH

  1. B239602
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B239604
    Remove the 3 screws.

  1. Using a clip remover, detach the 9 clips.

  1. B239606
    Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

  1. B239612
    Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

  1. B239616E02
    Disconnect each connector.
    Text in Illustration 
    *A
    for 14 Speakers
    *B
    for 9 Speakers

  1. B241320
    Using a screwdriver, detach the claw and remove the clamp.


5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B239615
    Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


6. REMOVE REAR SPEAKER SET

  1. B239136
    Disconnect the connector.

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the rear speaker set.

    NOTICE:
    Do not touch the cone of the speaker.


7. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B239620
    Disconnect the connector.

  1. Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


8. REMOVE REAR DOOR GLASS RUN LH

  1. B239628
    Remove the rear door glass run.


9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. B239630E01
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window division bar sub-assembly.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.


10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B239632
    Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B239636
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B239640E01
    Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


12. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

  1. B239642E01
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.


13. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B242868
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →