2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

  1. B239600
    Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.


3. REMOVE ASSIST GRIP COVER LH

  1. B239602
    Using moulding remover A, detach the 8 claws and remove the assist grip cover.


4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B239604
    Remove the 3 screws.

  1. Using a clip remover, detach the 9 clips.

  1. B239606
    Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

  1. B239612
    Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

  1. B239616E02
    Disconnect each connector.
    Text in Illustration 
    *A
    for 14 Speakers
    *B
    for 9 Speakers

  1. B241320
    Using a screwdriver, detach the claw and remove the clamp.


5. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B239615
    Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B238973
    Detach the 2 claws and remove the rear power window regulator switch assembly.


7. REMOVE REAR REFLEX REFLECTOR ASSEMBLY

  1. E198065
    Detach the 2 claws and remove the rear reflex reflector assembly.


8. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

  1. E200180E01
    Disconnect the connector.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and remove the light.

    HINT:
    Tape the screwdriver tip before use.


9. REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

  1. E198055
    Disconnect the connector.

  1. Detach the clamp.

  1. Turn the light in the direction indicated by the arrow and remove it.


10. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B239610
    Remove the 8 screws and rear door armrest.

  1. B239618
    Remove the 2 screws.

  1. Detach the guide and 2 claws and remove the rear door inside handle sub-assembly from the rear door trim board sub-assembly.


11. REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)

  1. B239137
    Remove the 2 screws and No. 2 speaker.

    NOTICE:
    Do not touch the cone of the speaker.


12. REMOVE REAR SPEAKER SET

  1. B239136
    Disconnect the connector.

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the rear speaker set.

    NOTICE:
    Do not touch the cone of the speaker.


13. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B239620
    Disconnect the connector.

  1. Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.


14. REMOVE REAR DOOR GLASS RUN LH

  1. B239628
    Remove the rear door glass run.


15. REMOVE REAR DOOR FRAME GARNISH LH

  1. B240621
    Detach the clip and remove the rear door frame garnish.


16. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. B239630E01
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window division bar sub-assembly.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.


17. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B239632
    Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


18. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

  1. B241321
    Remove the rear door quarter window weatherstrip from the rear door quarter window glass.


19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

  1. Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B239636
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.

  1. B239640E01
    Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the door glass.


20. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

  1. B234457E02
    Using a screwdriver, remove the rear door glass channel sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


21. REMOVE REAR DOOR GLASS CHANNEL FILLER
  1. Remove the rear door glass channel filler.


22. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

  1. B239642E01
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.


23. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B242868
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.


24. REMOVE REAR DOOR LOCK ASSEMBLY LH

  1. B237876E01
    Using a T30 "TORX" wrench, remove the 3 screws.
    Text in Illustration 
    *A
    w/o Double Locking System
    *B
    w/ Double Locking System
    V100135
    Slide

  1. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.


25. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B239650E03
    Using a screwdriver, detach the claw.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System

    HINT:
    Tape the screwdriver tip before use.

  1. B239652E04
    Remove the rear door lock remote control cable assembly.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System


26. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B239654E03
    Using a screwdriver, detach the 3 claws.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System

    HINT:
    Tape the screwdriver tip before use.

  1. B239656E02
    Remove the rear door inside locking cable assembly.
    Text in Illustration 
    *A
    w/ Double Locking System
    *B
    w/o Double Locking System


27. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

  1. B239658
    Using a T30 "TORX" socket wrench, loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. Detach the claw and remove the rear door outside handle cover.


28. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B239662
    Move the lever in the direction indicated by the arrow in the illustration.

  1. B239664
    Remove the rear door outside handle assembly as shown in the illustration.


29. REMOVE REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH

  1. B239668
    Detach the 3 claws and remove the rear door No. 1 outside handle pad.


30. REMOVE REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH

  1. B239670
    Detach the 2 claws and remove the rear door No. 2 outside handle pad.


31. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B239672
    Using a T30 "TORX" socket wrench, loosen the screw.

  1. Slide the rear door outside handle frame sub-assembly to detach the door handle nut and claw of the rear door outside handle frame sub-assembly, and then remove the rear door outside handle frame sub-assembly.


32. REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH

  1. B239676
    Using a clip remover, detach the 6 clips and guide and remove the rear door No. 2 weatherstrip as shown in the illustration.


33. REMOVE REAR DOOR CHECK ASSEMBLY LH

  1. B239622
    Remove the bolt, 2 nuts and rear door check assembly.


34. REMOVE REAR DOOR WEATHERSTRIP LH

  1. B239624
    Using a clip remover, detach the 19 clips and guide and remove the rear door weatherstrip.


35. REMOVE REAR DOOR BELT MOULDING LH

B241010E01
  1. Detach the 7 claws and remove the rear door belt moulding.

    Text in Illustration 
    *1
    Protective Tape


36. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

  1. B243913
    Remove the door window frame moulding clip.

  1. B243912E01
    Put protective tape around the rear door front window frame moulding.

  1. Using a moulding remover, detach the clip and remove the double-sided tape to remove the rear door front window frame moulding.

    Text in Illustration 
    *1
    Protective Tape
    *2
    Double-sided Tape
    *3
    Moulding Remover


37. REMOVE NO. 2 BLACK OUT TAPE LH

B236343
  1. Pull back an edge of the No. 2 black out tape and pull it parallel to the vehicle body to remove it.


38. REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH

B236346
  1. Pull back an edge of the rear door lower outside stripe and pull it parallel to the vehicle body to remove it.


39. REMOVE BLACK OUT TAPE LH

B236348
  1. Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.


40. REMOVE REAR DOOR OUTSIDE STRIPE LH

B236350
  1. Pull back an edge of the rear door outside stripe and pull it parallel to the vehicle body to remove it.


41. REMOVE REAR DOOR PANEL CUSHION

  1. B240622
    Using a clip remover, detach the clip and remove the door panel cushion.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2014) →