2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FAN SHROUD
  1. Remove the fan shroud (Click here).


3. REMOVE VANE PUMP DRIVE PULLEY

A223614
  1. Remove the 4 bolts, vane pump drive pulley and cooler compressor drive pulley.


4. REMOVE CRANKSHAFT PULLEY

A058720E02
  1. Using SST, remove the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. A058719E02
    Using SST, remove the pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-60010   (09951-00490)
    09950-40011   (09957-04010)
    Text in Illustration 
    *a
    Hold
    *b
    Turn


5. REMOVE IDLE PULLEY ASSEMBLY

  1. A224977
    Remove the 2 bolts and Idle pulley bracket.


6. REMOVE TIMING BELT COVER

  1. A112017
    Remove the 11 bolts, washers, timing belt cover, and 2 gaskets.


7. REMOVE TIMING BELT GUIDE
  1. Remove the timing belt guide.


8. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A058728E03
    Using the crankshaft pulley bolt, align the groove of the crankshaft pulley with the timing pointer by turning the crankshaft clockwise.
    Text in Illustration 
    *1
    Timing Mark
    V100135
    Turn

  1. A058729E02
    Check that the timing marks of the camshaft timing pulley and No. 2 timing belt cover are aligned.
    Text in Illustration 
    *1
    Timing Mark
    If not, turn the crankshaft 1 revolution (360°).


9. REMOVE TIMING BELT

HINT:
If reusing the timing belt, draw a direction arrow on the timing belt (in the direction the belt move when the engine is running), and place matchmarks on the pulleys and timing belt.

  1. A058730
    Turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.
    Text in Illustration 
    V100135
    Turn

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when removing the camshaft timing pulley, and camshaft causing damage. Therefore, always set the crankshaft pulley is removed at the correct angle.

  1. A058731E02
    Loosen the No. 1 timing belt idler bolt (A), and shift the idler to the left as far as possible.
    Text in Illustration 
    V100135
    Pry
    V100136
    Move

  1. Tighten the No. 1 timing belt idler bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.


10. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
  1. Remove the 2 bolts (A and B).

  1. A056838E06
    Loosen the bolt (C), and remove the No. 1 timing belt idler.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →