DTC No.
|
Detection Item
|
Fail-safe Operation
|
Fail-safe Deactivation Condition
|
P0031
|
Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P0032
|
Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P0046
|
Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance
|
The engine power is limited.
|
Engine switch off
|
P0047
|
Turbocharger/ Supercharger Boost Control "A" Circuit Low
|
The engine power is limited.
|
Engine switch off
|
P0048
|
Turbocharger/ Supercharger Boost Control "A" Circuit High
|
The engine power is limited.
|
Engine switch off
|
P007C
|
Charge Air Cooler Temperature Sensor Circuit Low
|
The intake air temperature is fixed at a specified value.
|
Pass condition detected
|
P007D
|
Charge Air Cooler Temperature Sensor Circuit High
|
The intake air temperature is fixed at a specified value.
|
Pass condition detected
|
P0087
|
Fuel Rail/System Pressure - Too Low
|
The engine power is reduced by 90%.*
|
Engine switch off
|
P0088
|
Fuel Rail/System Pressure - Too High
|
The engine power is reduced by 90%.*
|
Engine switch off
|
P0093
|
Fuel System Leak Detected - Large Leak
|
The engine power is reduced by 90%.*
|
Engine switch off
|
P0100
|
Mass Air Flow Circuit Malfunction
|
The engine power is limited.
|
Pass condition detected
|
P0101
|
Mass or Volume Air Flow Circuit
|
The engine power is limited.
|
Engine switch off
|
P0107
|
Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
|
The turbo pressure is fixed at a specified value.
|
Pass condition detected
|
P0108
|
Manifold Absolute Pressure/Barometric Pressure Circuit High Input
|
The turbo pressure is fixed at a specified value.
|
Pass condition detected
|
P0112
|
Intake Air Temperature Circuit Low Input
|
The intake air temperature value is fixed.
|
Pass condition detected
|
P0113
|
Intake Air Temperature Circuit High Input
|
The intake air temperature value is fixed.
|
Pass condition detected
|
P0115
|
Engine Coolant Temperature Circuit
|
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions).
|
Pass condition detected
|
P0117
|
Engine Coolant Temperature Circuit Low Input
|
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions).
|
Pass condition detected
|
P0118
|
Engine Coolant Temperature Circuit High Input
|
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions).
|
Pass condition detected
|
P0122
|
Throttle/Pedal Position Sensor/Switch "A" Circuit Low Input
|
The engine power is limited.
|
Engine switch off
|
P0123
|
Throttle/Pedal Position Sensor/Switch "A" Circuit High Input
|
The engine power is limited.
|
Engine switch off
|
P0168
|
Fuel Temperature Too High
|
The injection volume and maximum injection volume are reduced.
|
Pass condition detected
|
P0180
|
Fuel Temperature Sensor "A" Circuit
|
The fuel temperature is fixed at a specified value.
|
Pass condition detected
|
P0182
|
Fuel Temperature Sensor "A" Circuit Low Input
|
The fuel temperature is fixed at a specified value.
|
Pass condition detected
|
P0183
|
Fuel Temperature Sensor "A" Circuit High Input
|
The fuel temperature is fixed at a specified value.
|
Pass condition detected
|
P0190
|
Fuel Rail Pressure Sensor Circuit
|
- The main and sub circuits of the fuel pressure sensor are malfunctioning:
- The engine power is reduced by 90%.*
- The main or sub circuit of the fuel pressure sensor is malfunctioning:
- The engine power is limited.
|
Engine switch off
|
P0191
|
Fuel Rail Pressure Sensor Circuit Range / Performance
|
- The main and sub circuits of the fuel pressure sensor are malfunctioning:
- The engine power is reduced by 90%.*
- The main or sub circuit of the fuel pressure sensor is malfunctioning:
- The engine power is limited.
|
Engine switch off
|
P0192
|
Fuel Rail Pressure Sensor Circuit Low Input
|
- The main and sub circuits of the fuel pressure sensor are malfunctioning:
- The engine power is reduced by 90%.*
- The main or sub circuit of the fuel pressure sensor is malfunctioning:
- The engine power is limited.
|
Engine switch off
|
P0193
|
Fuel Rail Pressure Sensor Circuit High Input
|
- The main and sub circuits of the fuel pressure sensor are malfunctioning:
- The engine power is reduced by 90%.*
- The main or sub circuit of the fuel pressure sensor is malfunctioning:
- The engine power is limited.
|
Engine switch off
|
P0201
|
Injector Circuit / Open - (Cylinder 1)
|
The engine power is limited.
|
Engine switch off to on (IG) or STA on
|
P0202
|
Injector Circuit / Open - (Cylinder 2)
|
The engine power is limited.
|
Engine switch off to on (IG) or STA on
|
P0203
|
Injector Circuit / Open - (Cylinder 3)
|
The engine power is limited.
|
Engine switch off to on (IG) or STA on
|
P0204
|
Injector Circuit / Open - (Cylinder 4)
|
The engine power is limited.
|
Engine switch off to on (IG) or STA on
|
P0234
|
Turbocharger / Supercharger Overboost Condition
|
The engine power is limited.
|
Pass condition detected
|
P0299
|
Turbocharger / Supercharger Underboost
|
The engine power is limited.
|
Pass condition detected
|
P0335
|
Crankshaft Position Sensor "A" Circuit
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P0339
|
Crankshaft Position Sensor "A" Circuit Intermittent
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P0340
|
Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P0400
|
Exhaust Gas Recirculation Flow
|
The engine power is limited.
|
Engine switch off
|
P0405
|
Exhaust Gas Recirculation Sensor "A" Circuit Low
|
The engine power is limited.
|
Engine switch off
|
P0406
|
Exhaust Gas Recirculation Sensor "A" Circuit High
|
The engine power is limited.
|
Engine switch off
|
P042E
|
Exhaust Gas Recirculation "A" Control Stuck Open
|
The engine power is limited.
|
Engine switch off
|
P0488
|
Exhaust Gas Recirculation Throttle Position Control Range/Performance
|
The engine power is limited.
|
Engine switch off
|
P0489
|
Exhaust Gas Recirculation Control Circuit Low
|
The engine power is limited.
|
Engine switch off
|
P0490
|
Exhaust Gas Recirculation Control Circuit High
|
The engine power is limited.
|
Engine switch off
|
P0500
|
Vehicle Speed Sensor "A"
|
The vehicle speed is fixed at 0 km/h (0 mph).
|
Pass condition detected
|
P0522
|
Engine Oil Pressure Sensor/Switch Low
|
The oil pressure is maintained at a normal oil pressure (high oil pressure control mode).
|
Pass condition detected
|
P0523
|
Engine Oil Pressure Sensor/Switch High
|
The oil pressure is maintained at a normal oil pressure (high oil pressure control mode).
|
Pass condition detected
|
P0524
|
Engine Oil Pressure Too Low
|
The oil pressure is maintained at a normal oil pressure (high oil pressure control mode).
|
Pass condition detected
|
P0545
|
Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P0546
|
Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P0606
|
ECM / PCM Processor
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P060A
|
Internal Control Module Monitoring Processor Performance
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P060B
|
Internal Control Module A/D Processing Performance
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P0627
|
Fuel Pump Control Circuit / Open
|
The engine power is limited.
|
Pass condition detected
|
P062D
|
No. 1 Fuel Injector Driver Circuit Performance
|
The engine is stalled.
|
Engine switch off
|
P1229
|
Fuel Pump System
|
The engine power is limited.
|
Engine switch off
|
P1251
|
Turbocharger / Supercharger Overboost Condition (Too High)
|
The engine power is limited.
|
Engine switch off
|
P1271
|
Fuel Regulator Circuit Malfunction (EDU Drive)
|
The engine power is limited.
|
Engine switch off
|
P1272
|
Fuel Pressure Regulator Malfunction
|
The engine power is limited.
|
Engine switch off
|
P1626
|
Idle Signal Output Value Too Low
|
The engine power is limited.
|
Engine switch off
|
P1627
|
Idle Signal Output Value Too High
|
The engine power is limited.
|
Engine switch off
|
P2006
|
Intake Manifold Runner Control Stuck Closed (Bank 1)
|
The engine power is limited.
|
Engine switch off
|
P200C
|
Diesel Particulate Filter Over Temperature Bank 1
|
PM forced regeneration is prohibited.
|
Engine switch off
|
P2032
|
Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P2033
|
Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P2084
|
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P20CB
|
Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open
|
PM forced regeneration is prohibited.
|
Engine switch off
|
P20CD
|
Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit
|
- The engine power is reduced by 90%.*
- PM forced regeneration is prohibited.
|
Pass condition detected
|
P20CE
|
Short in Exhaust Aftertreatment Fuel Injector "A" Control Circuit
|
PM forced regeneration is prohibited.
|
Engine switch off
|
P20CF
|
Exhaust Aftertreatment Fuel Injector "A" Stuck Open
|
The engine power is reduced by 90%.*
|
Pass condition detected
|
P2120
|
Throttle/Pedal Position Sensor/Switch "D" Circuit
|
The engine power is limited.
|
Engine switch off
|
P2121
|
Throttle/Pedal Position Sensor/Switch "D" Circuit Range/Performance
|
The engine power is limited.
|
Engine switch off
|
P2122
|
Throttle/Pedal Position Sensor/Switch "D" Circuit Low Input
|
The engine power is limited.
|
Engine switch off
|
P2123
|
Throttle/Pedal Position Sensor/Switch "D" Circuit High Input
|
The engine power is limited.
|
Engine switch off
|
P2125
|
Throttle/Pedal Position Sensor/Switch "E" Circuit
|
The engine power is limited.
|
Engine switch off
|
P2127
|
Throttle/Pedal Position Sensor/Switch "E" Circuit Low Input
|
The engine power is limited.
|
Engine switch off
|
P2128
|
Throttle/Pedal Position Sensor/Switch "E" Circuit High Input
|
The engine power is limited.
|
Engine switch off
|
P2138
|
Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation
|
The engine power is limited.
|
Engine switch off
|
P2195
|
Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P2226
|
Barometric Pressure Circuit
|
The atmospheric pressure is fixed at a specified value.
|
Pass condition detected
|
P2228
|
Barometric Pressure Circuit Low Input
|
The atmospheric pressure is fixed at a specified value.
|
Pass condition detected
|
P2229
|
Barometric Pressure Circuit High Input
|
The atmospheric pressure is fixed at a specified value.
|
Pass condition detected
|
P2237
|
Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P2238
|
Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P2239
|
Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P2252
|
Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P2253
|
Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)
|
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped.
|
Pass condition detected
|
P242B
|
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P242C
|
Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P242D
|
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3
|
PM forced regeneration is prohibited.
|
Pass condition detected
|
P244A
|
Diesel Particulate Filter Differential Pressure Too Low
|
PM forced regeneration is prohibited.
|
Engine switch off
|
P244B
|
Diesel Particulate Filter Differential Pressure Too High
|
- The engine power is limited.
- PM forced regeneration is prohibited.
|
Engine switch off
|
P244C
|
Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1
|
PM forced regeneration is prohibited.
|
Engine switch off
|
P2463
|
Diesel Particulate Filter Restriction - Soot Accumulation
|
- The engine power is limited.
- PM forced regeneration is prohibited.
|
Pass condition detected
|
P2564
|
Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit Low
|
The engine power is limited.
|
Engine switch off
|
P2565
|
Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit High
|
The engine power is limited.
|
Engine switch off
|