2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE FRONT OIL PUMP BODY O-RING

D025646E01

2. FIX OIL PUMP ASSEMBLY

Q003426E03
  1. Place the oil pump body on the torque converter clutch.

    Text in Illustration 
    *1
    Torque converter clutch


3. REMOVE CLUTCH DRUM OIL SEAL RING

AT08412E01
  1. Remove the 2 oil seal rings.


4. REMOVE STATOR SHAFT ASSEMBLY

AT08411E01
  1. Remove the 13 bolts and stator shaft from the oil pump body.

  1. Remove the oil pump body from the torque converter clutch.


5. INSPECT FRONT OIL PUMP BODY

AT05153E01
  1. Using a dial indicator, measure the inside diameter of the oil pump body bush.

    Maximum inside diameter:
    38.19 mm (1.50 in.)

    If the inside diameter is more than the maximum, replace the oil pump body.


6. INSPECT STATOR SHAFT ASSEMBLY

AT05357E01
  1. Using a dial indicator, measure the inside diameter of the stator shaft bush.

    Maximum Inside Diameter:
    Front Side
    Rear Side
    21.58 mm (0.8496 in.)
    27.08 mm (1.0661 in.)

    If the inside diameter is more than the maximum, replace the stator shaft.


7. INSPECT CLEARANCE OF FRONT OIL PUMP BODY

AT00153E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the body clearance.

    Standard body clearance:
    0.07 to 0.15 mm (0.00276 to 0.00591 in.)

    Maximum body clearance:
    0.2 mm (0.00787 in.)

    If the body clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

  1. AT00154E01
    Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.004 to 0.248 mm (0.000157 to 0.00976 in.)

    Maximum tip clearance:
    0.3 mm (0.0118 in.)

    If the tip clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

  1. AT00155E01
    Using a steel straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.000787 to 0.00197 in.)

    Maximum side clearance:
    0.1 mm (0.00394 in.)

    If the side clearance is more than the maximum, replace the drive gear, driven gear or pump body assembly. Replace the part or parts determined to be the most likely cause of the problem.

    HINT:
    There are 5 different thicknesses for drive and driven gears.

    Drive and Driven Gear Thickness:
    Mark
    Specified Condition
    M
    11.690 to 11.699 mm (0.4602 to 0.4606 in.)
    N
    11.700 to 11.709 mm (0.4606 to 0.4610 in.)
    P
    11.710 to 11.720 mm (0.4610 to 0.4614 in.)
    R
    11.721 to 11.730 mm (0.4615 to 0.4618 in.)
    S
    11.731 to 11.740 mm (0.4618 to 0.4622 in.)


8. REMOVE FRONT OIL PUMP DRIVE GEAR

D025799E01

9. REMOVE FRONT OIL PUMP DRIVEN GEAR

D025800E01

10. REMOVE FRONT OIL PUMP OIL SEAL

AT05152E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the bush or oil pump body.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →