2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. BEARING POSITION

C171522E01

Bearing and Race Diameter:
Mark
Front Race Diameter Inside/Outside
Thrust Bearing Diameter Inside/Outside
Rear Race Diameter Inside/Outside
A
74.3 to 74.6 mm (2.93 to 2.94 in.)/87.4 to 87.7 mm (3.44 to 3.45 in.)
72.0 to 72.3 mm (2.83 to 2.85 in.)/85.3 to 85.6 mm (3.36 to 3.37 in.)
-
B
37.0 to 37.3 mm (1.46 to 1.47 in.)/52.1 to 52.3 mm (2.05 to 2.06 in.)
34.7 to 34.9 mm (1.366 to 1.374 in.)/51.6 to 51.9 mm (2.03 to 2.04 in.)
-
C
-
21.4 to 21.6 mm (0.841 to 0.850 in.)/40.8 to 41.0 mm (1.606 to 1.614 in.)
22.7 to 22.9 mm (0.892 to 0.902 in.)/60.0 to 60.4 mm (2.36 to 2.38 in.)
D
33.3 to 33.5 mm (1.31 to 1.32 in.)/56.3 to 56.6 mm (2.22 to 2.23 in.)
38.5 to 38.7 mm (1.515 to 1.524 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.)
-
E
-
42.6 to 42.8 mm (1.68 to 1.69 in.)/60.8 to 61.1 mm (2.39 to 2.41 in.)
-
F
38.0 to 38.2 mm (1.496 to 1.504 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.)
43.4 to 43.6 mm (1.71 to 1.72 in.)/58.0 to 58.4 mm (2.28 to 2.30 in.)
-
G
-
55.8 to 56.0 mm (2.197 to 2.204 in.)/76.1 to 76.4 mm (2.996 to 3.008 in.)
53.8 to 54.0 mm (2.12 to 2.13 in.)/73.7 to 74.0 mm (2.90 to 2.91 in.)
H
33.4 to 33.6 mm (1.31 to 1.32 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
32.2 to 32.3 mm (1.268 to 1.272 in.)/49.0 to 49.2 mm (1.93 to 1.94 in.)
32.2 to 32.4 mm (1.27 to 1.28 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
I
-
21.5 to 21.8 mm (0.846 to 0.858 in.)/40.5 to 40.8 mm (1.59 to 1.61 in.)
-
J
-
43.6 to 43.9 mm (1.72 to 1.73 in.)/60.6 to 60.9 mm (2.39 to 2.40 in.)
47.2 to 47.4 mm (1.86 to 1.87 in.)/66.9 to 67.1 mm (2.63 to 2.64 in.)


2. ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE

D028795E11
  1. Coat 2 new O-rings with ATF and install them to the brake reaction sleeve.

    Text in Illustration 
    *1
    New O-Ring

  1. Coat 2 new O-rings with ATF and install them to the No. 4 brake piston.

  1. Install the No. 4 brake piston to the reaction sleeve.


3. INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE

D028080E03
  1. Install the No. 4 brake piston with brake reaction sleeve to the transmission case.

    NOTICE:
    1. Do not damage the O-rings.
    2. Make sure the No. 4 brake piston is underneath the brake reaction sleeve.


4. INSTALL 1ST AND REVERSE BRAKE PISTON

D028081E03
  1. Coat a new O-ring with ATF.

  1. Install the O-ring to the 1st and reverse brake piston.

  1. With the spring seat of the piston facing upwards (the front side), install the piston to the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.


5. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

D028549E01
  1. Install the brake return spring to the 1st and reverse brake piston.

  1. D028082E02
    Place SST on the spring retainer and compress the return spring.
    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)
    Text in Illustration 
    *1
    Snap Ring


6. INSTALL REAR PLANETARY GEAR ASSEMBLY

D027947E02
  1. Install the No. 9 thrust bearing race.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    Race J
    47.2 to 47.4 mm (1.86 to 1.87 in.)
    66.9 to 67.1 mm (2.63 to 2.64 in.)

  1. C190076E02
    Coat the 2 thrust needle roller bearings with petroleum jelly and install them to the rear planetary gear.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing J
    43.6 to 43.9 mm (1.72 to 1.73 in.)
    60.6 to 60.9 mm (2.39 to 2.40 in.)
    Bearing I
    21.5 to 21.8 mm (0.846 to 0.858 in.)
    40.5 to 40.8 mm (1.59 to 1.61 in.)

    Text in Illustration 
    *1
    Bearing I
    *2
    Bearing J

  1. C190075
    Install the rear planetary gear assembly.


7. SELECT 1ST AND REVERSE BRAKE FLANGE

  1. D029831E01
    Using a vernier caliper, measure distance A (from the top surface of the 1st and reverse brake piston to the step in the transmission case) in the illustration.

    NOTICE:
    Make sure the 1st and reverse brake piston is installed securely to the transmission case.

    HINT:
    Distance A = 36.35 to 37.09 mm (1.43 to 1.46 in.)

  1. D029832E03
    Assemble the 2 flanges, 8 discs and 7 plates, and using a vernier caliper, measure distance B in the illustration at both ends across the diameter, and calculate the average.

    HINT:
    Distance B = 36.04 to 37.14 mm (1.42 to 1.46 in.)

  1. Select a 1st and reverse brake flange so that the value of measured distance A minus distance B is 2.85 to 3.15 mm (0.112 to 0.124 in.).

    Flange H Thickness:
    No.
    Thickness
    0
    0 mm (0 in.)
    2
    0.15 to 0.25 mm (0.00590 to 0.00984 in.)
    4
    0.35 to 0.45 mm (0.0138 to 0.0177 in.)
    6
    0.55 to 0.65 mm (0.0217 to 0.0256 in.)
    8
    0.75 to 0.85 mm (0.0295 to 0.0335 in.)
    10
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    12
    1.15 to 1.25 mm (0.0453 to 0.0492 in.)
    14
    1.35 to 1.45 mm (0.0531 to 0.0571 in.)


8. INSTALL NO. 4 BRAKE DISC

D027944E05
  1. Install the 2 flanges, 8 discs and 7 plates.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1

    Text in Illustration 
    *1
    Flange
    *2
    Disc
    *3
    Plate


9. INSTALL BRAKE PLATE STOPPER SPRING

D027943E01

10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

D027965E15
  1. Install the thrust bearing race, thrust needle roller bearing, thrust bearing race and planetary ring gear flange to the intermediate shaft.

    Thrust Needle Roller Bearing and Race Diameter:
    Item
    Inside
    Outside
    Race H Rear
    32.2 to 32.4 mm (1.27 to 1.28 in.)
    48.7 to 49.0 mm (1.92 to 1.93 in.)
    Bearing H
    32.2 to 32.3 mm (1.268 to 1.272 in.)
    49.0 to 49.2 mm (1.93 to 1.94 in.)
    Race H Front
    33.4 to 33.6 mm (1.31 to 1.32 in.)
    48.7 to 49.0 mm (1.92 to 1.93 in.)

    Text in Illustration 
    *1
    Race H Rear
    *2
    Race H Front


11. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

D027964E01
  1. Install the 1-way clutch and 1-way clutch inner race to the intermediate shaft.


12. INSTALL INTERMEDIATE SHAFT

D027942E01
  1. Install the intermediate shaft with No. 3 1-way clutch assembly to the case.

  1. D027927E03
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


13. INSTALL CENTER PLANETARY GEAR ASSEMBLY

D027940E01
  1. Install the planetary sun gear and center planetary gear to the case.

  1. Coat the thrust bearing race with petroleum jelly and install it to the center planetary gear.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    Race G
    53.8 to 54.0 mm (2.12 to 2.13 in.)
    73.7 to 74.0 mm (2.90 to 2.91 in.)


14. INSTALL NO. 2 BRAKE PISTON

  1. D028797E10
    Coat 2 new O-rings with ATF and install them to the brake piston.
    Text in Illustration 
    *1
    New O-Ring

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. Install the No. 2 brake piston to the case.


15. INSTALL NO. 2 BRAKE DISC

D027938E07
  1. Install the brake piston return spring.

  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange

  1. D028818E06
    Using SST and a press, compress the return spring and install the No. 2 brake spring snap ring.
    SST
    09351-40010  


16. INSTALL NO. 1 BRAKE PISTON

D028539E13
  1. Coat 2 new O-rings with ATF and install them to the brake piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.


17. INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

D027935E01
  1. Install the No. 1 brake piston with No. 1 brake cylinder and the brake piston return spring to the transmission case.


18. INSTALL BRAKE PISTON RETURN SPRING SNAP RING

D028819E04
  1. Using SST and a press, compress the return spring and install the brake piston return spring snap ring.

    SST
    09351-40010  


19. SELECT NO. 1 BRAKE FLANGE

  1. D028815E01
    Using a feeler gauge, measure the distance between the snap ring and flange.

    HINT:
    0.42 to 0.72 mm (0.0165 to 0.0283 in.)

    If the distance is outside the specification, parts may have been assembled incorrectly. Perform the reassembly again. If the distance is still outside the specification, select No. 1 brake flange so that the value of measured distance is 0.42 to 0.72 mm (0.0165 to 0.0283 in.).

    Flange Thickness:
    Mark
    Thickness
    0
    1.95 to 2.05 mm (0.0768 to 0.0807 in.)
    1
    2.15 to 2.25 mm (0.0846 to 0.0886 in.)
    2
    2.35 to 2.45 mm (0.0925 to 0.0965 in.)
    3
    2.55 to 2.65 mm (0.100 to 0.104 in.)


20. INSTALL NO. 1 BRAKE DISC

D027933E07
  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange


21. INSTALL CENTER PLANETARY RING GEAR

  1. D028541E01
    Install the center planetary ring gear and front planetary ring gear flange to the front planetary ring gear.

  1. D028540E01
    Using a screwdriver, install the snap ring.


22. INSTALL FRONT PLANETARY RING GEAR

D027932E01
  1. Install the thrust needle roller bearing and front planetary ring gear to the case.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing G
    55.8 to 56.0 mm (2.197 to 2.204 in.)
    76.1 to 76.4 mm (2.996 to 3.008 in.)


23. INSTALL FRONT PLANETARY GEAR ASSEMBLY

D027931E10
  1. Install the thrust washer and thrust needle roller bearing.

  1. Coat the No. 5 thrust race with petroleum jelly and install it to the front planetary ring gear.

    Thrust Needle Roller Bearing and Race Diameter:
    Item
    Inside
    Outside
    Bearing F
    43.4 to 43.6 mm (1.71 to 1.72 in.)
    58.0 to 58.4 mm (2.28 to 2.30 in.)
    Race F
    38.0 to 38.2 mm (1.496 to 1.504 in.)
    56.5 to 57.0 mm (2.22 to 2.24 in.)

    Text in Illustration 
    *1
    Bearing F
    *2
    Race F

  1. D027930E01
    Install the front planetary gear assembly and 1-way clutch inner race to the case.


24. INSTALL 2ND BRAKE PISTON

D028546E13
  1. Coat 2 new O-rings with ATF and install them to the 2nd brake piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Press the 2nd brake cylinder into the 2nd brake piston with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. Install the return spring to the 2nd brake cylinder.

  1. D028817E04
    Using SST and a press, compress the return spring and install the snap ring.
    SST
    09351-40010  

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


25. INSTALL 2ND BRAKE CYLINDER

D027929E01
  1. Install the 2nd brake cylinder to the case.


26. INSTALL 1-WAY CLUTCH ASSEMBLY

D027928E01
  1. Install the thrust washer and 1-way clutch to the case.


27. INSTALL 2ND BRAKE PISTON HOLE SNAP RING

D027927E03
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)


28. INSTALL NO. 3 BRAKE DISC

D027926E07
  1. Install the cushion plate, 4 plates, 4 discs and flange to the case.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *4

    Text in Illustration 
    *1
    Cushion Plate
    *2
    Plate
    *3
    Disc
    *4
    Flange


29. INSTALL NO. 3 BRAKE SNAP RING

D027925E01
  1. Using a screwdriver, install the snap ring.


30. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

D028816E03
  1. Coat 2 new O-rings with ATF and install them to the direct clutch piston.

    Text in Illustration 
    *1
    New O-Ring

  1. D028517E01
    Install the direct clutch return spring and No. 2 clutch balancer to the direct clutch piston.

  1. Press the direct clutch piston into the clutch drum with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. D028514E06
    Place SST on the direct clutch piston and compress the return spring with a press.

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    SST
    09320-89010  
    09350-30020   (09350-07070)

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028536E10
    Position the end gap of the snap ring as shown in the illustration
    Text in Illustration 
    *1
    Stopper

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


31. INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

  1. D028513E03
    Coat a new O-ring with ATF and install it to the clutch drum.
    Text in Illustration 
    *1
    New O-Ring

  1. D028512E03
    Coat a new O-ring with ATF and install it to the reverse clutch piston.
    Text in Illustration 
    *1
    New O-Ring

  1. D028511E01
    Press the clutch drum into the reverse clutch piston with both hands.

    NOTICE:
    Be careful not to damage the O-ring.


32. INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D028510E03
    Coat a new O-ring with ATF and install it to the reverse clutch piston.
    Text in Illustration 
    *1
    New O-Ring

  1. Install the reverse clutch return spring to the reverse clutch piston.


33. INSTALL NO. 3 CLUTCH BALANCER

  1. D028509E04
    Place SST on the No. 3 clutch balancer and compress the clutch balancer with a press.
    SST
    09387-00070  
    09350-30020   (09350-07070)

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028534E03
    Position the end gap of the snap ring as shown in the illustration.

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


34. INSTALL DIRECT CLUTCH DISC

C162137E02
  1. for 1GR-FE:
    Install the 5 plates, 5 discs and reverse clutch flange to the clutch drum.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange

  1. C162138E02
    for 1KD-FTV:
    Install the 6 plates, 6 discs and reverse clutch flange to the clutch drum.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3

    Text in Illustration 
    *1
    Plate
    *2
    Disc
    *3
    Flange

  1. C162740
    Using a screwdriver, install the snap ring to the clutch drum.

  1. D029841E03
    Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying compressed air (392 kPa, 4.0 kgf/ cm2, 57 psi) into the oil hole as shown in the illustration.

    Standard moving distance (A) for 1GR-FE:
    0.55 to 0.85 mm (0.0217 to 0.0335 in.)

    Standard moving distance (A) for 1KD-FTV:
    0.65 to 0.95 mm (0.0256 to 0.0374 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position indicated by the shaded area in the illustration.

    If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    2
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    3
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    4
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    5
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    6
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    7
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    8
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    9
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    A
    3.75 to 3.85 mm (0.148 to 0.152 in.)

  1. Temporarily remove the snap ring, replace the flange with the selected flange and reinstall the snap ring.


35. SELECT REVERSE CLUTCH FLANGE

C162741
  1. Using a screwdriver, install the snap ring to the clutch drum.

    NOTICE:
    Make sure to install the direct clutch and reverse clutch snap rings so that their openings face opposite directions.

  1. C175544E03
    Install the 2 flanges, 5 discs, 4 plates, cushion plate and reverse clutch reaction sleeve to the clutch drum.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1 - *4

    Text in Illustration 
    *1
    Flange
    *2
    Disc
    *3
    Plate
    *4
    Cushion Plate

  1. D029844E01
    Using a screwdriver, install the hole snap ring.

  1. Using a dial indicator, measure the moving distance (A minus B) of the top surface of the reverse clutch piston (A) and cushion plate at both ends across the diameter (B) while applying compressed air (392 kPa, 4.0 kgf/ cm2, 57 psi) into the oil hole as shown in the illustration. Then choose a flange of an appropriate thickness from the table so that the measured value is within the standard range.

    D028538E03

    Standard moving distance (A minus B):
    0.56 to 0.86 mm (0.0220 to 0.0339 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.3 mm (0.130 in.)) to the position indicated by the shaded area in the illustration.

    HINT:
    Distance (A) = 1.05 to 2.15 mm (0.0413 to 0.0846 in.)
    Distance (B) = 0.72 to 1.08 mm (0.0283 to 0.0425 in.)

    Flange Thickness:
    Mark
    Thickness
    0
    2.75 to 2.85 mm (0.108 to 0.112 in.)
    1
    2.85 to 2.95 mm (0.112 to 0.116 in.)
    2
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    3
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    4
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    5
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    6
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    7
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    8
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    9
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    A
    3.75 to 3.85 mm (0.148 to 0.152 in.)

  1. D029843E01
    Remove the snap ring, reverse clutch reaction sleeve and rear clutch disc set from the clutch drum.


36. REMOVE REVERSE CLUTCH REACTION SLEEVE

D029844E01
  1. Using a screwdriver, remove the snap ring from the clutch drum.

  1. D029843E01
    Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs and 4 clutch plates from the reverse clutch hub.


37. INSTALL INPUT SHAFT OIL SEAL RING

  1. D029677E01
    Coat 3 new oil seal rings with ATF.

  1. Squeeze the ends of the 3 oil seal rings together, and then install them to the starter shaft groove.

    NOTICE:
    Do not excessively widen the rings.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.


38. INSTALL FORWARD CLUTCH PISTON

D028525E03
  1. Coat 2 new O-rings with ATF and install them to the forward clutch piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Install the forward clutch piston to the input shaft.


39. INSTALL NO. 1 CLUTCH BALANCER

D028523E03
  1. Coat a new O-ring with ATF and install it to the clutch balancer.

    Text in Illustration 
    *1
    New O-Ring

  1. D028522E01
    Install the forward clutch return spring and clutch balancer.

    NOTICE:
    Be careful not to damage the O-ring.

  1. D028521E02
    Place SST on the No. 1 clutch balancer and compress the return spring with a press.
    SST
    09350-30020   (09350-07040, 09350-07070)

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028535E03
    Position the end gap of the snap ring as shown in the illustration.

    NOTICE:
    Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


40. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

D028520E03
  1. for 1GR-FE:
    Install the 2 flanges, 6 discs and 5 plates to the input shaft assembly.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1

    Text in Illustration 
    *1
    Flange
    *2
    Disc
    *3
    Plate

  1. C115806E02
    for 1KD-FTV:
    Install the 2 flanges, 7 discs and 6 plates to the input shaft assembly.

    Install in order:
    *1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1

    Text in Illustration 
    *1
    Flange
    *2
    Disc
    *3
    Plate

  1. D028519E01
    Using a screwdriver, temporarily install the snap ring.

  1. D028537E03
    Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while applying compressed air (196 kPa, 2.0 kgf/ cm2, 28 psi) into the oil hole as shown in the illustration.

    Standard moving distance (A) for 1GR-FE:
    0.61 to 0.91 mm (0.0240 to 0.0358 in.)

    Standard moving distance (A) for 1KD-FTV:
    0.81 to 1.01 mm (0.0319 to 0.0398 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position indicated by the shaded area in the illustration.

    HINT:
    Moving distance (A): 0.26 to 1.36 mm (0.0102 to 0.0535 in.)

    If the moving distance (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

    Flange Thickness:
    Mark
    Thickness
    0
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    1
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    2
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    3
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    4
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    5
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    6
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    7
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    8
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    9
    3.85 to 3.95 mm (0.148 to 0.152 in.)
    A
    3.95 to 4.05 mm (0.152 to 0.159 in.)

  1. Temporarily remove the snap ring, replace the flange with the selected flange and reinstall the snap ring.


41. INSTALL INPUT SHAFT ASSEMBLY

  1. D028505E01
    Install the input shaft to the clutch drum.

  1. D028504E01
    Install the thrust needle roller bearing to the clutch drum.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing C
    21.4 to 21.6 mm (0.841 to 0.850 in.)
    40.8 to 41.0 mm (1.606 to 1.614 in.)


42. INSTALL MULTIPLE DISC CLUTCH HUB

  1. D028503E08
    Coat the 2 thrust bearing races with petroleum jelly and install them to the multiple disc clutch hub.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    No. 3 Race
    22.7 to 22.9 mm (0.892 to 0.902 in.)
    60.0 to 60.4 mm (2.36 to 2.38 in.)
    Race D
    33.3 to 33.5 mm (1.31 to 1.32 in.)
    56.3 to 56.6 mm (2.22 to 2.23 in.)

    Text in Illustration 
    *1
    No. 3 Race
    *2
    Race D

  1. D028502E01
    Install the multiple disc clutch hub to the clutch drum.


43. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. D028500E06
    Coat the 2 thrust needle roller bearings with petroleum jelly and install them to the forward clutch hub.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing D
    38.5 to 38.7 mm (1.515 to 1.524 in.)
    56.5 to 57.0 mm (2.22 to 2.24 in.)
    Bearing E
    42.6 to 42.8 mm (1.68 to 1.69 in.)
    60.8 to 61.1 mm (2.39 to 2.41 in.)

    Text in Illustration 
    *1
    Bearing D
    *2
    Bearing E

  1. D028001E01
    Install the forward clutch hub to the clutch drum.


44. INSTALL REAR CLUTCH DISC

  1. D027999E17
    Install the 5 discs, 4 plates, reverse clutch flange and clutch cushion plate to the reverse clutch hub.

    Install in order:
    *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *3 - *4

    Text in Illustration 
    *1
    Disc
    *2
    Plate
    *3
    Flange
    *4
    Cushion Plate


45. INSTALL REVERSE CLUTCH REACTION SLEEVE

  1. D027998E01
    Install the reverse clutch reaction sleeve to the reverse clutch hub.


46. INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

  1. D027997E01
    Install the reverse clutch hub to the clutch drum.

  1. D027996E01
    Using a screwdriver, install the snap ring to the clutch drum and input shaft.


47. INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

  1. D027994E01
    Coat the No. 2 clutch drum thrust washer with petroleum jelly and install it to the clutch drum.

  1. Install the 1-way clutch to the clutch drum.


48. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C177432E02
  1. Coat the 2 thrust needle roller bearings and clutch drum thrust washer with petroleum jelly and install them to the clutch drum and input shaft assembly.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing A
    72.0 to 72.3 mm (2.83 to 2.85 in.)
    85.3 to 85.6 mm (3.36 to 3.37 in.)
    Bearing B
    34.7 to 34.9 mm (1366 to 1.374 in.)
    51.6 to 51.9 mm (2.03 to 2.04 in.)

    Text in Illustration 
    *1
    Bearing A
    *2
    Bearing B

  1. D029833E01
    Install the clutch drum and input shaft assembly to the transmission case.


49. INSTALL OIL PUMP ASSEMBLY

C177431E02
  1. Coat the No. 1 and No. 2 thrust bearing races with petroleum jelly and install them to the front oil pump.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    Race A
    74.3 to 74.6 mm (2.93 to 2.94 in.)
    87.4 to 87.7 mm (3.44 to 3.45 in.)
    Race B
    37.0 to 37.3 mm (1.46 to 1.47 in.)
    52.1 to 52.3 mm (2.05 to 2.06 in.)

    Text in Illustration 
    *1
    Race A
    *2
    Race B

  1. D028796E04
    Coat a new O-ring with ATF and install it to the oil pump assembly.
    Text in Illustration 
    *1
    New O-Ring

  1. Slide the oil pump onto the input shaft, align the bolt holes of the oil pump assembly with the bolt holes of the transmission case and install the oil pump.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

    NOTICE:
    Do not excessively push on the oil pump, as the oil seal rings will stick to the direct clutch drum.

  1. D027921E01
    Install the 10 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


50. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

D028548E02
  1. Using SST and a hammer, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)

  1. Coat the lips of the oil seals with MP grease.


51. INSPECT INDIVIDUAL PISTON OPERATION

  1. D028547E02
    Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the O/D direct clutch, check with the C3 accumulator piston hole closed.
    If there is no sound, disassemble and check the installation condition of the parts.

    1. No. 2 clutch (C2)
    2. No. 3 clutch (C3)
    3. No. 1 clutch (C1)
    4. No. 3 brake (B3)
    5. No. 1 brake (B1)
    6. No. 2 brake (B2)
    7. No. 4 brake (B4)


52. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

D028798E03
  1. Install a new spacer to the manual valve lever.

    Text in Illustration 
    *1
    Spacer
    *2
    Manual Valve Lever

  1. Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the manual valve lever shaft.

  1. D028799E01
    Using a hammer, tap in a new spring pin.

  1. D028800E01
    Align the manual valve lever indentation with the spacer hole, and stake them together with a punch.

  1. Check that the shaft rotates smoothly.


53. INSTALL PARKING LOCK PAWL SHAFT

D028846E05
  1. Install the E-ring to the shaft.

    Text in Illustration 
    *1
    E-Ring
    *2
    Parking Lock Pawl
    *3
    Spring

  1. Install the parking lock pawl, shaft and spring.


54. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

D012709E01
  1. Connect the parking lock rod to the manual valve lever to install it.


55. INSTALL PARKING LOCK PAWL BRACKET

D012708E01
  1. Install the parking lock pawl bracket to the transmission case with the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. D028801E09
    Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked by the lock pawl.
    Text in Illustration 
    *1
    Manual Valve Lever
    *2
    Planetary Ring Gear
    *3
    Parking Lock Pawl


56. INSTALL C-1 ACCUMULATOR VALVE

  1. D028802E10
    Install the 2 springs and accumulator valve to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-1 Inner
    30.40 mm (1.20 in.)
    11.40 mm (0.449 in.)
    Pink
    C-1 Outer
    48.76 mm (1.92 in.)
    16.60 mm (0.654 in.)
    Light Green


57. INSTALL C-3 ACCUMULATOR PISTON

D028802E11
  1. Coat 2 new O-rings with ATF and install them to the piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Install the 2 springs and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-3 Inner
    44.0 mm (1.73 in.)
    14.0 mm (0.551 in.)
    Yellow
    C-3 Outer
    73.35 mm (2.89 in.)
    19.90 mm (0.784 in.)
    Red


58. INSTALL B-3 ACCUMULATOR PISTON

D028802E12
  1. Coat 2 new O-rings with ATF and install them to the piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    B-3
    70.5 mm (2.78 in.)
    19.7 mm (0.776 in.)
    Purple


59. INSTALL C-2 ACCUMULATOR PISTON

D028802E13
  1. Coat 2 new O-rings with ATF and install them to the piston.

    Text in Illustration 
    *1
    New O-Ring

  1. Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-2
    62.0 mm (2.44 in.)
    15.9 mm (0.626 in.)
    White


60. INSTALL BRAKE DRUM GASKET

D027969E01
  1. Install the 3 brake drum gaskets.


61. INSTALL TRANSMISSION CASE GASKET

D027968E11
  1. Install the 3 transmission case gaskets.


62. INSTALL CHECK BALL BODY

D027914E14
  1. Install the spring and check ball body.

    Text in Illustration 
    *1
    Spring
    *2
    Check Ball Body


63. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

C157293E02
  1. Insert the pin of the manual valve into the hole of the manual valve lever.

    Text in Illustration 
    *1
    Pin

  1. C157292E01
    Install the transmission valve body assembly with the 19 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    36 mm (1.42 in.) for bolt A
    25 mm (0.984 in.) for bolt B

  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


64. INSTALL TRANSMISSION WIRE

D027912E01
  1. Coat a new O-ring with ATF and install it to the transmission wire connector.

  1. Install the transmission wire harness.

  1. Install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C125285E03
    Connect the 7 solenoid connectors.

  1. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Temperature Sensor
    *2
    No. 2 Temperature Sensor

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A
    36 mm (1.42 in.) for bolt B

    Sensor Wire Harness 
    Wire Harness
    Color
    No. 1 temperature sensor
    Orange
    No. 2 temperature sensor
    Blue


65. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

D012703E01
  1. Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


66. INSTALL TRANSMISSION OIL CLEANER MAGNET

D027992E03
  1. Install the 4 magnets.


67. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Install a new gasket to the oil pan.

  1. Install the oil pan with the 20 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


68. INSTALL REAR TRANS CASE ADAPTOR OIL RECEIVER

C212492
  1. Install the trans case adaptor oil receiver to the rear adaptor transfer.

  1. Using snap ring pliers, install the snap ring.


69. INSTALL TRANSMISSION CASE ADAPTER REAR OIL SEAL

C177436E01
  1. Coat the lip of a new oil seal with ATF.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)

    Standard depth:
    0 to 0.5 mm (0 to 0.0197 in.)


70. INSTALL TRANSFER ADAPTER REAR
  1. Clean the threads of the bolts and case.

  1. C175554E02
    Apply seal packing or equivalent to the transmission case adapter and 8 bolts.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

    Seal diameter:
    1.0 to 1.5 mm (0.0394 to 0.0591 in.)

    Text in Illustration 
    *1
    Seal Packing

  1. C111208E07
    Install the transmission case adapter with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    50 mm (1.97 in.) for bolt A
    40 mm (1.57 in.) for bolt B


71. INSTALL AUTOMATIC TRANSMISSION HOUSING

C190068E04
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Install the transmission housing with the 10 bolts.

    Torque:
    for 14 mm head bolt A:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for 17 mm head bolt B:
    57 N*m{ 579 kgf*cm , 42 ft.*lbf }
    for 14 mm head bolt C:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    Text in Illustration 
    *A
    for 1GR-FE:
    *B
    for 1KD-FTV:


72. INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

C212491
  1. Coat a new O-ring with ATF and install it to the breather tube.

  1. Install the breather tube with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


73. INSTALL SPEED SENSOR

  1. C111258
    Coat 2 new O-rings with ATF and install one to each speed sensor.

  1. Install the 2 speed sensors.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


74. INSTALL OIL COOLER TUBE UNION

  1. C212490E01
    Coat a new O-ring with ATF and install one to each oil cooler tube union.

  1. Install the oil cooler tube union.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    Text in Illustration 
    *A
    w/ Warmer:
    *B
    w/o Warmer:


75. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903E01
  1. Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.

  1. C212493E01
    Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.

  1. Remove the control shaft lever.

  1. D025795E19
    Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    Text in Illustration 
    *1
    Neutral Basic Line
    *2
    Groove

  1. D027990E01
    Using a screwdriver, bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.


76. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

C212489
  1. Install the control shaft lever with the spring washer and nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }

← INSPECTION (from Aug 2013)INSPECTION (from Aug 2013) →