2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK NAVIGATION RECEIVER ASSEMBLY
E284973E03
  1. Disconnect the H54 and H56 navigation receiver assembly connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    H54-3 (ACC1) - H54-7 (GND1)
    GR - BR
    Power source (ACC)
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    11 to 14 V
    H54-4 (+B1) - H54-7 (GND1)
    R - BR
    Power source (+B)
    Always
    11 to 14 V
    H54-7 (GND1) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    H56-1 (IG) - H54-7 (GND1)
    L - BR
    Power source (IG)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

  3. Reconnect the H54 and H56 navigation receiver assembly connectors.

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    H56-2 (REV) - H54-7 (GND1)
    R - W-B
    Reverse signal
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    H55-11 (CA+) - H55-23 (CGND)
    B - Shielded
    Power source
    Ignition switch ON
    5.5 to 7.05 V
    H55-12 (V+) - H55-23 (CGND)
    R - Shielded
    Display signal
    Ignition switch ON, camera lens not covered, displaying an image
    Pulse generation (See waveform 1)
    Ignition switch ON, camera lens covered, blacking out screen
    Pulse generation (See waveform 2)
    H55-23 (CGND) - Body ground
    Shielded - Body ground
    Shielded ground
    Always
    Below 1 V

  5. E171712E24
    Using an oscilloscope, check the waveform.

    1. Waveform 1

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      H55-12 (V+) - H55-23 (CGND)
      Tool Setting
      200 mV/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, camera lens not covered, displaying an image

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2

      Measurement Condition 
      Item
      Content
      Terminal No. (Symbol)
      H55-12 (V+) - H55-23 (CGND)
      Tool Setting
      200 mV/DIV., 50 μs/DIV.
      Condition
      Ignition switch ON, camera lens covered, blacking out screen

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1
      *b
      Waveform 2
      *c
      Synchronized Signal
      *d
      Video Waveform

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DTC CHECK / CLEAR (Aug 2013 – Jul 2014) →