2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter in a vise between aluminum plates.

  1. Perform a pull-in test.

    1. Remove the nut, and then disconnect the lead wire from terminal C.

    2. A219641E02
      Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. A219642E01
    Perform a holding test.

    1. Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

      Text in Illustration 
      *1
      Terminal C
      If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. A219643
    Inspect the clutch pinion gear return.

    1. Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. A218205E02
    Perform an operation test without load.

    1. Connect the lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. Connect the battery and an ammeter to the starter as shown in the illustration.

      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30

    3. Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

      Specified current:
      90 A or less at 11.5 V

      If the result is not as specified, inspect the starter assembly.

      HINT:
      Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A218206E02
    Inspect the pull-in coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A218207E02
    Inspect the holding coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Switch Body
      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT BRUSH

  1. A062430E10
    Using a vernier caliper, measure the brush length.

    Standard length:
    15.5 mm (0.610 in.)

    Minimum length:
    8.5 mm (0.335 in.)

    Text in Illustration 
    *1
    Length
    *a
    Brush Holder Side
    *b
    Starter Yoke Side
    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Check the brush spring load.

    1. ST00019E13
      Take a pull scale reading immediately after the brush spring separates from the brush.

      Standard spring load:
      18 to 24 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf)

      Minimum spring load:
      12 N (1 kgf, 2.7 lbf)

      Text in Illustration 
      *1
      Brush
      *2
      Brush Spring
      If the spring load is less than the minimum, replace the starter brush holder assembly.

  1. G036824E03
    Inspect the insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush holder - Negative (-) brush holder
      Always
      10 Ω or higher

      If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. Inspect the field coil for an open circuit.

    1. A050093E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Lead wire - Brush
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

    2. A050418E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Starter yoke body - Brush
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

  1. A225234E01
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator for a short circuit.

    1. A225235E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Coil Core
      If the result is not as specified, replace the starter armature assembly.

  1. A219195
    Check the commutator circle runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum runout:
      0.05 mm (0.00197 in.)

      If the circle runout is more than the maximum, replace the starter armature assembly.

  1. A219196
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    30.0 mm (1.18 in.)

    Minimum diameter:
    29.0 mm (1.14 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A102634
    Using a vernier caliper, measure the undercut depth of the commutator.

    Standard undercut depth:
    0.6 mm (0.0236 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, replace the starter armature assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A223418
    Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter clutch sub-assembly.

  1. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
    If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →