2013-2015 Land Cruiser Prado · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

NOTICE:
When installing the parts indicated by arrows, coat them with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat the lip of a new vane pump housing oil seal with power steering fluid.

  1. G036583E01
    Using SST and a press, press in the oil seal.
    SST
    09950-60010  
    09950-70010   (09951-00280, 09951-07100)

    NOTICE:
    1. Make sure to install the oil seal so that it is facing in the correct direction.
    2. Be careful not to damage the oil seal.


2. INSTALL SHAFT WITH PULLEY
  1. Coat the shaft with power steering fluid.

  1. F051464E02
    Gradually insert the vane pump shaft with vane pump pulley.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. Do not damage the lip of the oil seal in the vane pump front housing.
    2. Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.


3. INSTALL FRONT VANE PUMP SIDE PLATE
  1. Coat a new No. 2 O-ring with power steering fluid.

  1. C065369E03
    Install the No. 2 O-ring to the front housing.

  1. Coat a new No. 1 O-ring with power steering fluid.

  1. C065368E07
    Install the No. 1 O-ring to the front side plate.

  1. F050370E01
    Install the front side plate to the front housing while aligning the semicircle-shaped cutouts of both parts.

    NOTICE:
    Be sure to install the plate in the correct position and so that it is facing the correct direction.


4. INSTALL VANE PUMP CAM RING

  1. F050371E03
    With the inscribed mark facing upward, install the vane pump cam ring to the vane pump front housing while aligning the semicircle-shaped cutouts of both parts.
    Text in Illustration 
    *a
    Inscribed Mark

    NOTICE:
    Be sure to install the cam ring in the correct position and so that it is facing the correct direction.


5. INSTALL VANE PUMP ROTOR

  1. C095038E01
    Install the vane pump rotor to the front vane pump housing.

    HINT:
    The vane pump can be installed with either side facing up.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. D030335E14
    Install the 10 vane pump plates.
    Text in Illustration 
    *a
    Round End
    *b
    Outward
    *c
    Inward

    NOTICE:
    Make sure that the round ends of the vane pump plates are facing outward.


6. INSTALL VANE PUMP SHAFT SNAP RING

  1. F051011
    Using a screwdriver and snap ring expander, install a new snap ring to the shaft with pulley.


7. INSTALL REAR VANE PUMP HOUSING

  1. F050373E01
    Coat a new O-ring with power steering fluid and install it to the rear housing.

  1. Align the straight pin of the rear housing with the hole created by the semicircle-shaped cutouts of the cam ring, front side plate and front housing. Then install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

    NOTICE:
    Make sure that the O-ring is not out of position before installing the rear vane pump housing.


8. SECURE VANE PUMP ASSEMBLY

  1. C215475E01
    Using SST, secure the vane pump between aluminum plates in a vise as shown in the illustration.
    SST
    09630-00014   (09631-00132)


9. INSPECT TOTAL PRELOAD

  1. C053369E01
    Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended Service Bolt:
    Item
    Specified Condition
    Thread diameter
    10 mm (0.394 in.)
    Thread pitch
    1.25 mm (0.0492 in.)
    Bolt length
    50 mm (1.97 in.)

  1. Using a torque wrench, check the pump rotating torque.

    Standard Rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    If the rotating torque is not as specified, check the installation of the housing oil seal.


10. INSTALL POWER STEERING OIL PRESSURE SWITCH (w/o VSC)
  1. Coat a new O-ring with power steering fluid and install it to the oil pressure switch.

  1. Install the oil pressure switch to the vane pump.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


11. INSTALL PRESSURE PORT UNION O-RING (w/o VSC)
  1. Coat the compression spring and flow control valve with power steering fluid.

  1. Install the compression spring.

  1. Install the flow control valve facing in the correct direction.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


12. INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY
  1. Coat a new O-ring with power steering fluid and install it to the vane pump reservoir.

  1. Install the vane pump reservoir to the vane pump with the 3 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


13. INSTALL VANE PUMP OIL RESERVOIR CAP SUB-ASSEMBLY
  1. Install the vane pump oil reservoir cap sub-assembly

← INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →