2013-2015 Land Cruiser Prado · Service Manual Brake

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE NO. 1 BRAKE ACTUATOR BRACKET

  1. F051421
    Using a 5 mm hexagon wrench, remove the bolt and No. 1 brake actuator bracket.

  1. F051180
    Using a screwdriver, disconnect the brake fluid level warning switch connector from the No. 1 brake actuator bracket.


2. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

  1. C172197E03
    Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir.
    Text in Illustration 
    *1
    Pin Punch

  1. C172198
    Remove the screw and pull out the brake master cylinder reservoir sub-assembly.

  1. Remove the master cylinder reservoir filler cap.


3. REMOVE MASTER CYLINDER RESERVOIR GROMMET

  1. F051181E01
    Remove the 3 reservoir grommets from the master cylinder reservoir.


4. REMOVE NO. 1 BRAKE ACTUATOR HOSE

  1. F051182E02
    Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.


5. REMOVE NO. 1 BRAKE ACTUATOR TUBE

  1. C213450
    Using a union nut wrench, remove the No. 1 brake actuator tube.


6. REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

  1. F051185E01
    Using a screwdriver, remove the 2 plugs.

  1. F051186E02
    Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.

  1. F051187
    Using a screwdriver, remove the clip.

  1. C217128E01
    Remove the brake booster with accumulator pump assembly from the brake master cylinder.

  1. Remove the 2 brake booster pump collars and 2 brake booster pump bushes from the brake booster with accumulator pump assembly.

  1. F051415E03
    Using a 4 mm hexagon wrench, remove the 2 pins.


7. REMOVE NO. 1 BRAKE BOOSTER PUMP BRACKET

  1. F051189E02
    Using a 5 mm hexagon wrench, remove the 2 bolts and No. 1 brake booster pump bracket from the brake master cylinder solenoid.

  1. Remove the brake booster pump bush from the No. 1 brake booster pump bracket.


8. REMOVE NO. 3 BRAKE ACTUATOR BRACKET

  1. F051423
    Remove the bolt and No. 3 brake actuator bracket from the brake master cylinder.


9. REMOVE BRAKE BOOSTER ACCUMULATOR PIPE

  1. C217129
    Secure the brake booster with accumulator pump assembly in a vise.

  1. Remove the brake booster accumulator.

  1. Remove the O-ring from the brake booster accumulator.

    NOTICE:
    Make sure no foreign matter enters the pump.

  1. Remove the brake booster accumulator pipe and compression spring.


10. REMOVE MASTER CYLINDER SOLENOID

  1. F051195E02
    Remove the 6 bolts and master cylinder solenoid.

  1. F051196
    Remove the gasket.


11. REMOVE MASTER CYLINDER PUSH ROD CLEVIS

  1. C177091
    Loosen the lock nut on the rod operating adapter and remove the push rod clevis and lock nut.

  1. F051192E02
    Loosen the lock nut on the brake master cylinder side and remove the rod operating adapter and lock nut.


12. REMOVE MASTER CYLINDER BOOT

13. REMOVE BRAKE BOOSTER PISTON SUB-ASSEMBLY

  1. F051417E05
    Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body and then remove it with another screwdriver.
    Text in Illustration 
    *1
    C-Ring
    *2
    Pin

    HINT:
    Pressing the piston in with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body and then remove it with another screwdriver.

  1. Remove the plug from the piston.

  1. Remove the piston by pulling it straight out, not at an angle.

    NOTICE:
    If the piston pulled out at an angle, there is a possibility that the cylinder bore could be damaged.

← REMOVAL (from Aug 2014)INSPECTION (from Aug 2013) →