2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE FRONT BUMPER COVER LOWER
  1. Remove the clip, 5 bolts and front bumper cover lower.


2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts.

  1. A224743
    Unhook the engine under cover from the vehicle body as shown in the illustration.


3. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


A273797E01
Text in Illustration 
*1
Reservoir Cap
*2
Radiator Cap
*3
Radiator Drain Cock Plug
*4
Cylinder Block Drain Cock Plug
  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the cylinder block drain cock plug and drain the coolant from the engine.


5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


6. REMOVE OIL FILTER ELEMENT

  1. A094910E09
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A222100
    Remove the oil filter drain plug.

  1. A222101E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    HINT:
    Use a container to catch the draining oil.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

  1. A222102
    Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A222103E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A153538E03
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.


7. DISCONNECT WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A225377
    Remove the 3 bolts.

  1. A222108
    Disconnect the 2 hoses and water by-pass pipe.


8. REMOVE OIL FILTER BRACKET

  1. A223672E01
    Remove the 2 nuts, bolt, oil filter bracket and gasket.
    Text in Illustration 
    *A
    w/ Oil Cooler
    *B
    w/o Oil Cooler


9. REMOVE OIL COOLER ASSEMBLY

  1. A222109
    A222110
    Remove the 2 hoses.

  1. Remove the bolt, nut and oil cooler.

  1. Remove the seal washer from the bolt.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →