2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSPECT 6TH GEAR THRUST CLEARANCE

F051109E01
  1. Using a dial indicator, measure the 6th gear thrust clearance.

    Standard clearance:
    0.20 to 0.49 mm (0.00788 to 0.0193 in.)

    If the clearance is outside the specification, replace the gear, spacer or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


2. INSPECT 3RD GEAR THRUST CLEARANCE

F051110E01
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard clearance:
    0.09 to 0.52 mm (0.00355 to 0.0205 in.)

    If the clearance is outside the specification, replace the gear, thrust washer, clutch hub or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


3. INSPECT 4TH GEAR THRUST CLEARANCE

F051111E01
  1. Using a dial indicator, measure the 4th gear thrust clearance.

    Standard clearance:
    0.12 to 0.38 mm (0.00473 to 0.0150 in.)

    If the clearance is outside the specification, replace the gear, clutch hub or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


4. INSPECT 6TH GEAR RADIAL CLEARANCE

F051106E01
  1. Using a dial indicator, measure the 6th gear radial clearance.

    Standard clearance:
    0.015 to 0.065 mm (0.000591 to 0.00255 in.)

    If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


5. INSPECT 3RD GEAR RADIAL CLEARANCE

F051107E01
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard clearance:
    0.015 to 0.067 mm (0.000591 to 0.00263 in.)

    If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


6. INSPECT 4TH GEAR RADIAL CLEARANCE

F051108E01
  1. Using a dial indicator, measure the 4th gear radial clearance.

    Standard clearance:
    0.015 to 0.051 mm (0.000591 to 0.00200 in.)

    If the clearance is outside the specification, replace the gear, needle roller bearing or shaft.

    HINT:
    Replace the part or parts determined to be the most likely cause of the problem.


7. REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

D033652E01
  1. Using 2 screwdrivers and a hammer, tap off the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


8. REMOVE 6TH GEAR SUB-ASSEMBLY

C216335E01
  1. Using SST and a press, remove the No. 3 transmission clutch hub, hub sleeve, synchronizer ring and 6th gear from the input shaft.

    SST
    09950-00020  
    09950-70010   (09951-07200)
    09950-60010   (09951-00300)

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand so that it does not fall.


9. REMOVE 6TH GEAR NEEDLE ROLLER BEARING
  1. Remove the 6th gear needle roller bearing from the input shaft.


10. REMOVE SPACER
  1. Remove the spacer from the input shaft.


11. REMOVE GEAR THRUST WASHER SHAFT SNAP RING

D033654E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.


12. REMOVE 3RD GEAR THRUST WASHER
  1. Remove the 3rd gear thrust washer from the input shaft.


13. REMOVE 3RD GEAR
  1. Remove the 3rd gear from the input shaft.


14. REMOVE STRAIGHT PIN
  1. Remove the straight pin from the input shaft.


15. REMOVE 3RD GEAR NEEDLE ROLLER BEARING
  1. Remove the 3rd gear needle roller bearing from the input shaft.


16. REMOVE SPACER
  1. Remove the spacer from the input shaft.


17. REMOVE NO. 2 SYNCHRONIZER RING SET

F051095E01
  1. Remove the No. 2 synchronizer ring set from the input shaft.


18. REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

D033657E01
  1. Using a snap ring expander, remove the snap ring from the input shaft.


19. REMOVE 4TH GEAR

C216336E01
  1. Using SST and a press, remove the No. 2 transmission clutch hub, hub sleeve, synchronizer ring and 4th gear from the input shaft.

    SST
    09950-00020  
    09950-60010   (09951-00300)
    09950-70010   (09951-07200)

    NOTICE:
    Support the input shaft by hand so that it does not fall.


20. REMOVE 4TH GEAR NEEDLE ROLLER BEARING
  1. Remove the 4th gear needle roller bearing from the input shaft.


21. REMOVE INPUT SHAFT FRONT BEARING SNAP RING

D033659E01
  1. Using 2 screwdrivers and a hammer, tap off the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


22. REMOVE INPUT SHAFT FRONT BEARING

C216337E01
  1. Using SST and a press, remove the input shaft front bearing from the input shaft.

    SST
    09950-00020  

    NOTICE:
    Support the input shaft by hand so that it does not fall.


23. REMOVE NO. 2 TRANSMISSION CLUTCH HUB

C136406E02
  1. Remove the clutch hub, 3 synchromesh shifting keys, 3 balls and 3 springs from the hub sleeve.

    Text in Illustration 
    *1
    Spring
    *2
    Ball
    *3
    Synchronizer Shifting Key

    HINT:
    Use a piece of cloth to prevent the balls and springs from flying off.


24. REMOVE NO. 3 TRANSMISSION CLUTCH HUB

HINT:
Perform the same procedure as for the No. 2 clutch hub.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →