B15D5 Rear Seat Entertainment System Disconnected
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
- *1: w/ Navigation System (for Navigation Receiver Type)
- *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System
When an AVC-LAN communication error occurs between the navigation receiver assembly*1 or radio and display receiver assembly*2 and television display assembly, this DTC will be stored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D5 |
When either condition below is met:
|
|
- HINT:
- Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- The navigation receiver assembly*1 or radio and display receiver assembly*2 is the master unit.
- Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B15D5 is not output.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTOR CONNECTION CONDITION |
Check that the television display assembly and navigation receiver assembly*1 or radio and display receiver assembly*2 connectors are connected properly.
- *1: w/ Navigation System (for Navigation System)
- *2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System
- OK:
- The connectors are connected properly.
- *1: w/ Navigation System (for Navigation System)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the television display assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
W14-17 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
W14-1 (+B) - Body ground
Always
11 to 14 V
W14-2 (ACC) - Body ground
Ignition switch ACC
11 to 14 V
| *a |
Front view of wire harness connector (to Television Display Assembly) |
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY OR RADIO AND DISPLAY RECEIVER ASSEMBLY- TELEVISION DISPLAY ASSEMBLY) |
w/ Navigation System (for Navigation System)
Disconnect the H57 navigation receiver assembly connector.
w/ Navigation System (for Radio and Display Type) or w/o Navigation System
Disconnect the H52 radio and display receiver assembly connector.
Disconnect the W14 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- w/ Navigation System (for Navigation System):
Tester Connection
Condition
Specified Condition
H57-9 (TX+) - W14-3 (TX1+)
Always
Below 1 Ω
H57-10 (TX-) - W14-4 (TX1-)
Always
Below 1 Ω
H57-9 (TX+) - Body ground
Always
10 kΩ or higher
H57-10 (TX-) - Body ground
Always
10 kΩ or higher
- w/ Navigation System (for Radio and Display Type) or w/o Navigation System:
Tester Connection
Condition
Specified Condition
H52-9 (TX+) - W14-3 (TX1+)
Always
Below 1 Ω
H52-10 (TX-) - W14-4 (TX1-)
Always
Below 1 Ω
H52-9 (TX+) - Body ground
Always
10 kΩ or higher
H52-10 (TX-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK TELEVISION DISPLAY ASSEMBLY |
Temporarily replace the television display assembly with a new or known good one (Click here).
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B15D5 is not output.
Result Result
Proceed to
OK
A
NG (w/ Navigation System [for Navigation System])
B
NG (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)
C
|
|
||||
|
|
||||
| A | ||
| ||
