2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0201 Injector Circuit / Open - (Cylinder 1)

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The injector driver (EDU) delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the injector driver (EDU) receives a fuel injection command (#1 to #4) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the fuel injector.
A210270E30
P0201, P0202, P0203, P0204: 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 seconds
Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
  1. Open or short in injector driver circuit
  2. Injector assembly
  3. Injector driver
  4. ECM
P062D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 seconds
Inconsistency in the injection waveforms between the injector driver and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
  1. Open or short in injector driver circuit
  2. Injector assembly
  3. Injector driver
  4. ECM

MONITOR DESCRIPTION

  1. P0201, P0202, P0203, P0204:
    The ECM compares injection command (# 1 to # 4) signals and injection confirmation (INJF) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203 or P0204 will be stored.
  1. P062D:
    The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals and INJF signals are inconsistent.
    The fuel injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the fuel injector. When the fuel injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
    After the engine is started, when there is no injection confirmation (INJF) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver (EDU), DTC P062D is stored.
    If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the engine switch is turned off.
    A145849E12

WIRING DIAGRAM

A246629E01
A246630E02

INSPECTION PROCEDURE

CAUTION:
Make sure to perform work on high voltage circuits with the engine switch off.

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Engine does not start*1
    A
    Engine starts, but idling is rough*2
    B
    Except above
    C

    HINT:
    1. *1: Once DTC P062D is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
      When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Fuel Press" is higher than the value for "Target Common Rail Pressure"
    2. *2: DTC P0201, P0202, P0203, P0204 and P062D are stored at this time.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. INSPECT ECM

  1. A255625E01
    Check the waveform of the ECM connectors using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    C90-21 (#1) - C93-1 (E1)
    Cranking
    Correct waveform is as shown
    C90-22 (#2) - C93-1 (E1)
    Cranking
    Correct waveform is as shown
    C90-23 (#3) - C93-1 (E1)
    Cranking
    Correct waveform is as shown
    C90-24 (#4) - C93-1 (E1)
    Cranking
    Correct waveform is as shown

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 11
OK


3. CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE

  1. A204910E14
    Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C121-2 (+B) - C121-4 (GND)
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver)

  1. Reconnect the injector driver connectors.



NG
Go to step 14
OK


4. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
  1. Disconnect the injector driver connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C124-7 (#10) - C90-21 (#1)
    Always
    Below 1 Ω
    C124-3 (#20) - C90-22 (#2)
    Always
    Below 1 Ω
    C124-6 (#30) - C90-23 (#3)
    Always
    Below 1 Ω
    C124-4 (#40) - C90-24 (#4)
    Always
    Below 1 Ω
    C124-8 (INJF) - C90-20 (INJF)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C124-7 (#10) or C90-21 (#1) - Body ground
    Always
    10 kΩ or higher
    C124-3 (#20) or C90-22 (#2) - Body ground
    Always
    10 kΩ or higher
    C124-6 (#30) or C90-23 (#3) - Body ground
    Always
    10 kΩ or higher
    C124-4 (#40) or C90-24 (#4) - Body ground
    Always
    10 kΩ or higher
    C124-8 (INJF) or C90-20 (INJF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reconnect the ECM connector.



NG
Go to step 14
OK


5. REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 15
6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch is turned on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds.

  1. Start the engine and idle it for 30 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Check the DTCs output on the tester.

    HINT:
    1. The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.
    2. If the DTC P0201 is output, check the No. 1 injector assembly circuit.
    3. If the DTC P0202 is output, check the No. 2 injector assembly circuit.
    4. If the DTC P0203 is output, check the No. 3 injector assembly circuit.
    5. If the DTC P0204 is output, check the No. 4 injector assembly circuit.


NEXT


7. INSPECT INJECTOR DRIVER

  1. A255604E01
    Disconnect the injector assembly connectors for all cylinders.

    NOTICE:
    If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.

  1. Check the waveform of the injector assembly connectors using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    C115-1 - C115-2
    Cranking
    Voltage increases by 50 V or more
    C116-1 - C116-2
    Cranking
    Voltage increases by 50 V or more
    C117-1 - C117-2
    Cranking
    Voltage increases by 50 V or more
    C118-1 - C118-2
    Cranking
    Voltage increases by 50 V or more

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Assembly)



NG
Go to step 12
OK


8. REPLACE FUEL INJECTOR (RELEVANT CYLINDER)
  1. Replace the injector assembly of the cylinder relevant to the DTC (Click here).

    NOTICE:
    1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
    2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.


NEXT


9. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


10. REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
  1. Register the injector compensation code (Click here).

  1. Perform the fuel injector pilot quantity learning (Click here).



NEXT
Go to step 15
NEXT


11. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 15
12. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - INJECTOR DRIVER)
  1. Disconnect the fuel injector connectors.

  1. Disconnect the injector driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C115-1 - C122-1 (IJ1+)
    Always
    Below 1 Ω
    C115-2 - C122-4 (IJ1-)
    Always
    Below 1 Ω
    C116-1 - C122-3 (IJ2+)
    Always
    Below 1 Ω
    C116-2 - C122-6 (IJ2-)
    Always
    Below 1 Ω
    C117-1 - C121-1 (IJ3+)
    Always
    Below 1 Ω
    C117-2 - C121-3 (IJ3-)
    Always
    Below 1 Ω
    C118-1 - C122-2 (IJ4+)
    Always
    Below 1 Ω
    C118-2 - C122-5 (IJ4-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C115-1 or C122-1 (IJ1+) - Body ground
    Always
    10 kΩ or higher
    C115-2 or C112-4 (IJ1-) - Body ground
    Always
    10 kΩ or higher
    C116-1 or C122-3 (IJ2+) - Body ground
    Always
    10 kΩ or higher
    C116-2 or C122-6 (IJ2-) - Body ground
    Always
    10 kΩ or higher
    C117-1 or C121-1 (IJ3+) - Body ground
    Always
    10 kΩ or higher
    C117-2 or C121-3 (IJ3-) - Body ground
    Always
    10 kΩ or higher
    C118-1 or C122-2 (IJ4+) - Body ground
    Always
    10 kΩ or higher
    C118-2 or C122-5 (IJ4-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector connectors.

  1. Reconnect the injector driver connectors.



NG
Go to step 14
OK


13. REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 15
14. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


15. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds or more.

  1. Start the engine and idle it for 10 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0191 Fuel Rail Pressure Sensor Circuit Range / Performance (from Aug 2014)P0201 Injector Circuit / Open - (Cylinder 1) (+ P0202, P0203, P0204, P062D) (from Aug 2014) →