2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0627 Fuel Pump Control Circuit / Open

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

P0627 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 1 second
Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
  1. Open or short in suction control valve circuit
  2. Suction control valve
  3. ECM
Related Data List 
DTC No.
Data List
P0627
  1. Fuel Press
  2. Target Common Rail Pressure

HINT:
  1. For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here).
  2. When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
    Under a stable operating condition such as idling, Fuel Press is within 5000 kPa of Target Common Rail Pressure.


WIRING DIAGRAM

Refer to DTC P0088 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

  1. A239632E03
    Disconnect the suction control valve connector.
    Text in Illustration 
    *1
    Fuel Supply Pump Assembly
    *2
    Suction Control Valve

  1. Measure the resistance of the suction control valve.

    OK:
    No open or short circuit malfunction.



NG
Go to step 4
OK


2. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
  1. Disconnect the suction control valve connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C71-1 - C92-23 (PCV+)
    Always
    Below 1 Ω
    C71-2 - C92-12 (PCV-)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C71-1 or C92-23 (PCV+) - Body ground
    Always
    10 kΩ or higher
    C71-2 or C92-12 (PCV-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


3. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and idle it for 1 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0627 is output
    B



B
Go to step 7
A

END

4. REPLACE SUCTION CONTROL VALVE
  1. Replace the suction control valve (Click here).


NEXT


5. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


6. PERFORM FUEL SUPPLY PUMP INITIALIZATION
  1. Perform fuel supply pump initialization (Click here).



NEXT
Go to step 9
7. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 9
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds or more.

  1. Start the engine and idle it for 1 second or more.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0627 Fuel Pump Control Circuit / Open (Aug 2013 – Jul 2014)P062F Internal Control Module EEPROM Error (Aug 2013 – Jul 2014) →