2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for the LH and RH sides.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL QUARTER WINDOW ASSEMBLY LH

B239031E01
  1. Using a brush or sponge, apply primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

    Text in Illustration 
    *1
    Primer M
    *2
    Adhesive
    *a
    CORRECT
    *b
    INCORRECT

  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.

    B239033E02

    Text in Illustration 
    *1
    Adhesive
    -

    *a
    Backside
    *b
    Adhesive Center Line

    Standard:
    Area
    Specified Condition
    a
    7.0 mm (0.276 in.)
    b
    8.0 mm (0.315 in.)
    c
    6.5 mm (0.256 in.)

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Apply adhesive to the quarter window glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      B239034E02

      Text in Illustration 
      *1
      Adhesive
      -

      *a
      Backside
      *b
      Adhesive Center Line

      Standard:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      6.5 mm (0.256 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load a sealer gun with the cartridge.

    3. Apply adhesive to the quarter window glass as shown in the illustration.

  1. Install the quarter window glass to the vehicle body.

    1. B242858
      Attach the 4 clips to install the quarter window assembly LH.

      NOTICE:
      Allow the primer to dry for 3 minutes or more.

    2. Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check the clearance between the body and glass.

    3. Lightly press the front surface of the glass to ensure a close fit.

    4. BO03986E07
      Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive to any areas where the amount of adhesive is inadequate.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours

      Text in Illustration 
      *1
      Adhesive


2. CHECK FOR LEAK AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.


3. INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH

B242802E01
  1. Install a new clip A to the roof side rail garnish.

    Text in Illustration 
    *1
    New Clip

  1. Attach the 3 clips to install the roof side rail garnish.


4. INSTALL ROOF HEADLINING ASSEMBLY
  1. Install the roof headlining assembly (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →