AVC-LAN Circuit
Circuit diagnosis · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Each navigation system component connected to the AVC-LAN (communication bus) transfers switch signals using the audio visual communication local area network.If a short to +B or short to ground occurs in the AVC-LAN, the audio system will not function normally because communication is not possible.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- The navigation receiver assembly is the master unit.
- When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
- The navigation receiver assembly is the master unit.
| 1. INSPECT NAVIGATION RECEIVER ASSEMBLY |
Remove the navigation receiver assembly (Click here).


Text in Illustration *A
w/ Rear Seat Entertainment System
*B
w/ Multi-terrain Monitor
*a
Component without harness connected
(Navigation Receiver Assembly)
-
-
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
7 (TX1+) - 8 (TX1-)
Always
60 to 80 Ω
9 (TX+) - 10 (TX-)*1
Always
60 to 80 Ω
7 (TX3+) - 8 (TX3-)*2
Always
60 to 80 Ω
- *1: w/ Rear Seat Entertainment System
- *2: w/ Side Monitor System
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT) |
- *1: w/ Rear Seat Entertainment System
- *2: w/ Side Monitor System
Disconnect the H55, H56 and H57 navigation receiver assembly connectors.
Disconnect the H63 stereo component amplifier assembly connector.
Disconnect the W14 television display assembly connector*1.
Disconnect the I6 parking assist ECU connector*2.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H55-7 (TX3+) - I6-11 (TX+)*2
Always
Below 1 Ω
H55-8 (TX3-) - I6-10 (TX-)*2
Always
Below 1 Ω
H56-7 (TX1+) - H63-8 (TX+)
Always
Below 1 Ω
H56-8 (TX1-) - H63-7 (TX-)
Always
Below 1 Ω
H57-9 (TX+) - W14-3 (TX1+)*1
Always
Below 1 Ω
H57-10 (TX-) - W14-4 (TX1-)*1
Always
Below 1 Ω
H55-7 (TX3+) - Body ground*2
Always
10 kΩ or higher
H55-8 (TX3-) - Body ground*2
Always
10 kΩ or higher
H56-7 (TX1+) - Body ground
Always
10 kΩ or higher
H56-8 (TX1-) - Body ground
Always
10 kΩ or higher
H57-9 (TX+) - Body ground*1
Always
10 kΩ or higher
H57-10 (TX-) - Body ground*1
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT MALFUNCTIONING PARTS |
Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.
- HINT:
- Check all slave units.
- When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.
- Check all slave units.
- OK:
- Master unit returns to normal operation.
|
|
||||
| OK | ||
| ||
