2013-2015 Land Cruiser Prado · Service Manual Brake

C1232 Acceleration Sensor Stuck Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are stored.
DTC Code
DTC Detection Condition
Trouble Area
C1232
At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or GL2 is below 80 mV and the fluctuation range of the signal of the other is higher than 1.9 V for 30 seconds or more.
  1. ECU-IG NO. 1 fuse
  2. Sensor installation
  3. Harness or connector
  4. Yaw rate and acceleration sensor
  5. CAN communication system
C1243
The following condition repeats 16 times.
  1. GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
C1245
The following condition continues for at least 60 seconds.
  1. The difference between the values calculated from the acceleration sensor value and vehicle speed exceeds 0.35 G.
C1279
Stored during test mode.

WIRING DIAGRAM

C185399E04

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the yaw rate and acceleration sensor, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Check if DTCs U0073, U0123, C1210 and/or C1336 are output (Click here).

    Result 
    Result
    Proceed to
    DTC U0073, U0123, C1210 and/or C1336 are not output
    A
    DTC U0073 and/or U0123 are output (for LHD)
    B
    DTC U0073 and/or U0123 are output (for RHD)
    C
    DTC C1210 and/or C1336 are output
    D



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2. CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Check that the yaw rate and acceleration sensor is installed properly.

    OK:
    The sensor is tightened to the specified torque. The sensor is not tilted.



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK


3. CHECK TERMINAL VOLTAGE AND RESISTANCE (IG, GND)
  1. Disconnect the G52 yaw rate and acceleration sensor connector.

  1. C208309E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G52-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G52-1 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)
Result 
Result
Proceed to
OK (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
A
OK (When troubleshooting in accordance with Problem Symptoms Table)
B
NG
C


B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)


← C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245, C1279) (Aug 2013 – Jul 2014)C1241 Low Power Supply Voltage Malfunction (Aug 2013 – Jul 2014) →