2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

PTC Heater Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.

WIRING DIAGRAM

E200726E02

INSPECTION PROCEDURE


1. INSPECT PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3)

  1. E199507
    Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3)
OK


2. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E197830E10
    Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 79°C (174°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    Below 1 V*
    G25-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 76°C (169°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    G25-4 (PTC3) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 73°C (163°F) or less
    5. Headlight dimmer switch off
    6. Blower switch off
    G25-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 79°C (174°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    11 to 14 V*
    G25-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 76°C (169°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    G25-4 (PTC3) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 73°C (163°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on

    Text in Illustration 
    *a
    Component with harness connected
    (Air Conditioning Amplifier Assembly)

    HINT:
    *: After the measurement conditions are met, wait 30 seconds before performing measurements.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - AIR CONDITIONING AMPLIFIER)
  1. Remove the PTC heater relays from the engine room No. 2 relay block.

  1. Disconnect the G25 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 1 - G25-3 (PTC1)
    Always
    Below 1 Ω
    PTC NO. 2 relay terminal 1 - G25-22 (PTC2)
    PTC NO. 3 relay terminal 1 - G25-4 (PTC3)
    PTC NO. 1 relay terminal 1 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 2 relay terminal 1 - Body ground
    PTC NO. 3 relay terminal 1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - QUICK HEATER)
  1. Remove the PTC heater relays from the engine room No. 2 relay block.

  1. Disconnect the G28 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 3 - G28-2 (B)
    Always
    Below 1 Ω
    PTC NO. 2 relay terminal 3 - G28-3 (B)
    PTC NO. 3 relay terminal 3 - G28-1 (B)
    PTC NO. 1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 2 relay terminal 3 - Body ground
    PTC NO. 3 relay terminal 3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 RELAY BLOCK - BATTERY AND BODY GROUND)

  1. E200727E02
    Remove the PTC heater relays from the engine room No. 2 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 5 - Body ground
    Always
    11 to 14 V
    PTC NO. 2 relay terminal 5 - Body ground
    PTC NO. 3 relay terminal 5 - Body ground

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 2 - Body ground
    Always
    Below 1 Ω
    PTC NO. 2 relay terminal 2 - Body ground
    PTC NO. 3 relay terminal 2 - Body ground

Text in Illustration 
*1
PTC NO. 1 Relay
*2
PTC NO. 2 Relay
*3
PTC NO. 3 Relay
*a
Component without relay installed
(Engine Room No. 2 Relay Block)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT QUICK HEATER ASSEMBLY

  1. E140255E08
    Remove the quick heater assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (B) - 1 (E)
    Always
    Below 1 kΩ
    2 (B) - 1 (E)
    2 (B) - 2 (E)
    3 (B) - 2 (E)



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND)

  1. E179945E10
    Disconnect the G29 heater connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G29-1 (E) - Body ground
    Always
    Below 1 Ω
    G29-2 (E) - Body ground

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Quick Heater Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Rear Air Conditioning Control Panel Circuit (from Aug 2014)PTC Heater Circuit (from Aug 2014) →