2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


2. REMOVE RADIATOR GRILLE

B357908E01
  1. Put protective tape around the radiator grille.

  1. Remove the 4 screws.

  1. Detach the 8 claws and remove the radiator grille.

    Text in Illustration 
    *1
    Protective Tape


3. REMOVE FRONT BUMPER COVER

  1. B353268
    Remove the 2 screws.

    HINT:
    Use the same procedure for the screws on the other side.

  1. B353353E01
    Remove the 2 screws.
    Text in Illustration 
    *1
    Screw
    *2
    Bolt A
    *3
    Bolt B

  1. Remove the 2 bolts labeled A and 2 bolts labeled B.

  1. B353270E01
    Put protective tape around the front bumper cover.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 4 clips.

  1. Detach the 16 claws and remove the front bumper cover.

    NOTICE:
    Do not hold the middle of the front bumper cover, as it may become reformed.

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Disconnect the 3 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Disconnect the connector.

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Disconnect the 2 connectors.

  1. w/ Headlight Cleaner System:
    Disconnect the No. 1 headlight cleaner hose.


4. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH

  1. E283270
    Extend the type 1 headlight washer nozzle sub-assembly LH by hand.

    NOTICE:
    Be careful not to damage the headlight washer actuator sub-assembly or type 1 headlight washer nozzle sub-assembly LH.

  1. Detach the claw and remove the type 1 headlight washer nozzle sub-assembly LH.


5. REMOVE TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


6. REMOVE NO. 1 HEADLIGHT CLEANER HOSE

  1. E283257
    Disconnect the No. 1 headlight cleaner hose from the headlight washer actuator sub-assembly.

  1. Detach the 5 clamps and remove the No. 1 headlight cleaner hose from the front bumper cover.


7. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH

  1. E283258E01
    Remove the headlight cleaner clamp as shown in the illustration.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp

  1. E283259E01
    Pull down the headlight cleaner clamp B and remove it.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp B

  1. Push the tab shown by arrow 1, detach the 2 claws and remove the headlight washer actuator sub-assembly LH as shown in the illustration.

    E283260E01


8. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH

  1. E283261E01
    Remove the headlight cleaner clamp as shown in the illustration.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp

  1. E283262E01
    Pull down the headlight cleaner clamp A and remove it.
    Text in Illustration 
    *1
    Headlight Cleaner Clamp A

  1. Push the tab shown by arrow 1, detach the 2 claws and remove the headlight washer actuator sub-assembly RH as shown in the illustration.

    E283263E01

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →