2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on "Bus Check".
  1. "ECM Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside ECM
  2. ECM
  1. For vehicles without a 5L-E engine.

WIRING DIAGRAM

C217303E01
C217303E03
C218090E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

  1. for 1GR-FE:

    1. Disconnect the C36, C37 and G55 ECM connectors.C217328E04

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C36-12 (E1) - Body ground
      Always
      Below 1 Ω
      C37-14 (E01) - Body ground
      Always
      Below 1 Ω
      C37-15 (E02) - Body ground
      Always
      Below 1 Ω
      C37-10 (ME01) - Body ground
      Always
      Below 1 Ω
      G55-12 (EC) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G55-24 (BATT) - Body ground
      Always
      11 to 14 V
      G55-23 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V
      G55-22 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G55-9 (MREL)
      11 to 14 V

  1. for 1KD-FTV:

    1. Disconnect the C93, G57 and G58 ECM connectors.C289505E01

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C93-1 (E1) - Body ground
      Always
      Below 1 Ω
      C93-12 (E01) - Body ground
      Always
      Below 1 Ω
      C93-13 (E02) - Body ground
      Always
      Below 1 Ω
      C93-8 (ME01) - Body ground
      Always
      Below 1 Ω
      G57-11 (EC) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G57-23 (BATT) - Body ground
      Always
      11 to 14 V
      G57-17 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V
      G57-24 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G58-11 (MREL)
      11 to 14 V

  1. for 2TR-FE:

    1. Disconnect the G59, G60 and C64 ECM connectors.C289505E02

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to ECM)
      -
      -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C64-5 (E1) - Body ground
      Always
      Below 1 Ω
      C64-11 (E01) - Body ground
      Always
      Below 1 Ω
      C64-12 (E02) - Body ground
      Always
      Below 1 Ω
      C64-13 (ME01) - Body ground
      Always
      Below 1 Ω
      G59-11 (EC) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G59-17 (BATT) - Body ground
      Always
      11 to 14 V
      G59-23 (+B) - Body ground
      Battery positive (+) voltage applied to terminal G60-12 (MREL)
      11 to 14 V

Result 
Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1KD-FTV)
B
OK (for 2TR-FE)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← ECM Communication Stop Mode (Aug 2013 – Jul 2014)Main Body ECU Communication Stop Mode (Aug 2013 – Jul 2014) →