2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

TERMINALS OF ECU

System information · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (for Windshield Wiper Switch LH Side Type)
E164993E06
  1. Disconnect the G120 windshield wiper switch connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G120-11 (+B) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    G120-11 (+B) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    G120-7 (WIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    G120-7 (WIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    G120-9 (EW) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the G120 windshield wiper switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G120-8 (WF) - Body ground
    B - Body ground
    Front washer motor output
    Front washer switch on
    Below 1 V
    G120-8 (WF) - Body ground
    B - Body ground
    Front washer motor output
    Front washer switch off
    11 to 14 V
    G120-4 (SPD) - Body ground
    R - Body ground
    Speed signal
    Driving at approx. 20 km/h (12 mph)
    Pulse generation (See waveform 1)
    G120-3 (TAIL) - Body ground
    V - Body ground
    Light control switch tail position signal input
    Light control switch in tail position
    11 to 14 V
    G120-3 (TAIL) - Body ground
    V - Body ground
    Light control switch tail position signal input
    Light control switch off
    Below 1 V
    G120-2 (+1) - Body ground
    B - Body ground
    Front wiper motor LO speed signal circuit
    Front wiper motor in LO operation
    11 to 14 V
    G120-2 (+1) - Body ground
    B - Body ground
    Front wiper motor LO speed signal circuit
    Front wiper motor off
    Below 1 V
    G120-1 (+2) - Body ground
    R - Body ground
    Front wiper motor HI speed signal circuit
    Front wiper motor in HI operation
    11 to 14 V
    G120-1 (+2) - Body ground
    R - Body ground
    Front wiper motor HI speed signal circuit
    Front wiper motor off
    Below 1 V
    G120-10 (+S) - Body ground
    W - Body ground
    Front wiper motor operation signal
    Front wiper motor operates
    11 to 14 V
    G120-10 (+S) - Body ground
    W - Body ground
    Front wiper motor operation signal
    Front wiper motor off
    Below 1 V
    G120-16 (C1R) - Body ground
    B - Body ground
    Rear wiper motor LO speed signal circuit
    Ignition switch ON, rear wiper switch LO
    Below 1 V
    G120-16 (C1R) - Body ground
    B - Body ground
    Rear wiper motor LO speed signal circuit
    Ignition switch ON, rear wiper switch off
    11 to 14 V
    G120-18 (+1R) - Body ground
    R - Body ground
    Rear wiper motor HI speed signal circuit
    Ignition switch ON, rear wiper switch HI
    Below 1 V
    G120-18 (+1R) - Body ground
    R - Body ground
    Rear wiper motor HI speed signal circuit
    Ignition switch ON, rear wiper switch off
    11 to 14 V
    G120-17 (WR) - Body ground
    V - Body ground
    Rear washer motor output
    Rear washer switch on
    Below 1 V
    G120-17 (WR) - Body ground
    V - Body ground
    Rear washer motor output
    Rear washer switch off
    11 to 14 V

  5. E149152E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G120-4 (SPD) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Driving at approx. 20 km/h (12 mph)


CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (for Windshield Wiper Switch RH Side Type)
E164993E06
  1. Disconnect the G120 windshield wiper switch connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G120-17 (+B) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    G120-17 (+B) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    G120-3 (WIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    G120-3 (WIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    G120-1 (EW) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the G120 windshield wiper switch assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G120-2 (WF) - Body ground
    B - Body ground
    Front washer motor output
    Front washer switch on
    Below 1 V
    G120-2 (WF) - Body ground
    B - Body ground
    Front washer motor output
    Front washer switch off
    11 to 14 V
    G120-6 (SPD) - Body ground
    R - Body ground
    Speed signal
    Driving at approx. 20 km/h (12 mph)
    Pulse generation (See waveform 1)
    G120-7 (TAIL) - Body ground
    V - Body ground
    Light control switch tail position signal input
    Light control switch in tail position
    11 to 14 V
    G120-7 (TAIL) - Body ground
    V - Body ground
    Light control switch tail position signal input
    Light control switch off
    Below 1 V
    G120-8 (+1) - Body ground
    B - Body ground
    Front wiper motor LO speed signal circuit
    Front wiper motor in LO operation
    11 to 14 V
    G120-8 (+1) - Body ground
    B - Body ground
    Front wiper motor LO speed signal circuit
    Front wiper motor off
    Below 1 V
    G120-9 (+2) - Body ground
    R - Body ground
    Front wiper motor HI speed signal circuit
    Front wiper motor in HI operation
    11 to 14 V
    G120-9 (+2) - Body ground
    R - Body ground
    Front wiper motor HI speed signal circuit
    Front wiper motor off
    Below 1 V
    G120-18 (+S) - Body ground
    W - Body ground
    Front wiper motor operation signal
    Front wiper motor operates
    11 to 14 V
    G120-18 (+S) - Body ground
    W - Body ground
    Front wiper motor operation signal
    Front wiper motor off
    Below 1 V
    G120-12 (C1R) - Body ground
    B - Body ground
    Rear wiper motor LO speed signal circuit
    Ignition switch ON, rear wiper switch LO
    Below 1 V
    G120-12 (C1R) - Body ground
    B - Body ground
    Rear wiper motor LO speed signal circuit
    Ignition switch ON, rear wiper switch off
    11 to 14 V
    G120-10 (+1R) - Body ground
    R - Body ground
    Rear wiper motor HI speed signal circuit
    Ignition switch ON, rear wiper switch HI
    Below 1 V
    G120-10 (+1R) - Body ground
    R - Body ground
    Rear wiper motor HI speed signal circuit
    Ignition switch ON, rear wiper switch off
    11 to 14 V
    G120-11 (WR) - Body ground
    V - Body ground
    Rear washer motor output
    Rear washer switch on
    Below 1 V
    G120-11 (WR) - Body ground
    V - Body ground
    Rear washer motor output
    Rear washer switch off
    11 to 14 V

  5. E149152E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G120-6 (SPD) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Driving at approx. 20 km/h (12 mph)


CHECK HEADLIGHT CLEANER CONTROL RELAY
E178109E04
  1. Disconnect the A38 headlight cleaner control relay connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A38-1 (HDLO) - A38-4 (E)
    V - W-B
    Low beam headlight signal
    Headlight dimmer switch in head
    11 to 14 V
    A38-1 (HDLO) - A38-4 (E)
    V - W-B
    Low beam headlight signal
    Headlight dimmer switch not in head
    Below 1 V
    A38-3 (IG) - A38-4 (E)
    L - W-B
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A38-3 (IG) - A38-4 (E)
    L - W-B
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A38-4 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    A38-5 (FRWA) - A38-4 (E)
    B - W-B
    Front washer switch operation signal
    Front washer motor switch on
    Below 1 V
    A38-5 (FRWA) - A38-4 (E)
    B - W-B
    Front washer switch operation signal
    Front washer motor switch off
    11 to 14 V


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
B235899E06
Text in Illustration 
*A
for LHD
*B
for RHD
  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    G63-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Install the main body ECU (multiplex network body ECU) (Click here).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G63-16 (HDLO) - G63-3 (GND2)
    V - W-B
    Low beam headlight signal
    Headlight dimmer switch in head
    11 to 14 V
    G63-16 (HDLO) - G63-3 (GND2)
    V - W-B
    Low beam headlight signal
    Headlight dimmer switch not in head
    Below 1 V
    G64-19 (BCTY) - G63-3 (GND2)
    G - W-B
    Back door courtesy light switch input
    Back door open
    Below 1 V
    G64-19 (BCTY) - G63-3 (GND2)
    G - W-B
    Back door courtesy light switch input
    Back door closed
    Pulse generation (See waveform 1 or 2)
    G64-1 (GCTY) - G63-3 (GND2)
    V - W-B
    Glass hatch courtesy switch input
    Glass hatch open
    Below 1 V
    G64-1 (GCTY) - G63-3 (GND2)
    V - W-B
    Glass hatch courtesy switch input
    Ignition switch off, all doors closed and glass hatch closed
    Pulse generation (See waveform 3 or 4)
    G63-20 (RWMR) - G63-3 (GND2)
    B - W-B
    Rear wiper power supply input
    Ignition switch ON, glass hatch open
    Below 1 V
    G63-20 (RWMR) - G63-3 (GND2)
    B - W-B
    Rear wiper power supply input
    Ignition switch ON, glass hatch closed
    11 to 14 V

  5. B199631E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-19 (BCTY) - G63-3 (GND2)
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Back door closed

  6. B199632E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-19 (BCTY) - G63-3 (GND2)
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Back door closed

  7. B199631E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-1 (GCTY) - G63-3 (GND2)
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and glass hatch closed

  8. B199632E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference)  
    Item
    Content
    Terminal No. (Symbol)
    G64-1 (GCTY) - G63-3 (GND2)
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch off, all doors closed and glass hatch closed

← TERMINALS OF ECU (Aug 2013 – Jul 2014)FAIL-SAFE CHART (from Aug 2013) →