2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

Image from Camera for Rear View Monitor is Abnormal

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the rear television camera assembly.

WIRING DIAGRAM

E286150E03

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the H55 navigation receiver assembly connector.

  1. Disconnect the X9*1 or v2*2 rear television camera assembly connector.

    1. *1: w/ Tire Carrier
    2. *2: w/o Tire Carrier

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/ Tire Carrier:
    Tester Connection
    Condition
    Specified Condition
    H55-11 (CA+) - X9-6 (CB+)
    Always
    Below 1 Ω
    H55-12 (V+) - X9-3 (CV+)
    Always
    Below 1 Ω
    H55-23 (CGND) - X9-5 (CGND)
    Always
    Below 1 Ω
    H55-24 (V-) - X9-2 (CV-)
    Always
    Below 1 Ω
    H55-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    H55-12 (V+) - Body ground
    Always
    10 kΩ or higher
    H55-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    H55-24 (V-) - Body ground
    Always
    10 kΩ or higher
    w/o Tire Carrier:
    Tester Connection
    Condition
    Specified Condition
    H55-11 (CA+) - v2-6 (CB+)
    Always
    Below 1 Ω
    H55-12 (V+) - v2-3 (CV+)
    Always
    Below 1 Ω
    H55-23 (CGND) - v2-5 (CGND)
    Always
    Below 1 Ω
    H55-24 (V-) - v2-2 (CV-)
    Always
    Below 1 Ω
    H55-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    H55-12 (V+) - Body ground
    Always
    10 kΩ or higher
    H55-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    H55-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E280624E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H55-23 (CGND) - Body ground
    Always
    Below 1 Ω
    H55-24 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H55-11 (CA+) - Body ground
    Ignition switch ON
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E275625E12

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    H55-12 (V+) - H55-23 (CGND)
    Tool Setting
    200 mV/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, camera lens not covered, displaying an image
    2. Waveform 2: Ignition switch ON, camera lens covered, blacking out screen

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Tire Carrier)
    B
    NG (w/o Tire Carrier)
    C



B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)

C
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Image from Camera for Rear View Monitor is Abnormal (Aug 2013 – Jul 2014)PRECAUTION (from Aug 2013) →