2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL ENGINE REAR OIL SEAL

  1. A102145E03
    Apply a light coat of MP grease to the lip of a new oil seal.

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the oil seal.
    2. Do not allow MP grease to contact the dust seal.

  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07150)

    NOTICE:
    1. Wipe off any extra grease from the crankshaft.
    2. Do not tap in the oil seal at an angle.


2. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. G038107E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A222356E01
    Install the front spacer, drive plate and rear spacer to the crankshaft.
    Text in Illustration 
    *1
    Front Drive Plate Spacer
    *2
    Drive Plate and Ring Gear
    *3
    Rear Drive Plate Spacer
    V100135
    Transmission Side

    HINT:
    1. The front drive plate spacer is reversible.
    2. As the rear drive plate spacer and drive plate and ring gear are not reversible, be sure to install it so that it is facing in the direction shown in the illustration.

  1. Clean the bolts and bolt holes.

  1. Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A222355E01
    Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not start the engine for at least an hour after installing the drive plate.


3. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. G038107E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. Clean the bolts and bolt holes.

  1. Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A222354E01
    Install and uniformly tighten the 10 bolts in several steps in the sequence shown in the illustration.

    Torque:
    27 N*m{ 270 kgf*cm , 20 ft.*lbf }

  1. Mark the top of the bolts with paint.

  1. Tighten the 10 bolts 90° in the same sequence.

  1. Check that the paint marks are now at a 90° angle to the top.


4. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C215534E01
    Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel to install the clutch disc.
    SST
    09301-00110  
    Text in Illustration 
    V100135
    Flywheel Side

    NOTICE:
    Be sure to install the clutch disc so that it is facing in the correct direction.


5. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

C215535E01
  1. Align the matchmarks on the clutch cover and flywheel.

    Text in Illustration 
    *a
    Matchmark

  1. Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    HINT:
    Move SST up and down, and right and left lightly after checking that the clutch disc assembly is in the center, and then tighten the bolts.


6. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
  1. Install the manual transaxle assembly (Click here).


7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
  1. Install the automatic transmission assembly (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →