2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

C1ABD Short to +B in Buzzer

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. DTC C1ABD is stored when the blind spot monitor sensor RH detects a +B short in RCTA buzzer (blind spot monitor buzzer) circuit.
  2. DTC C1ABE is stored when the blind spot monitor sensor RH detects a ground short or open in RCTA buzzer (blind spot monitor buzzer) circuit.
DTC Code
DTC Detection Condition
Trouble Area
C1ABD
  1. Both of the following conditions are met:
    1. Blind spot monitor main switch assembly (multi-function switch) is on with engine switch on (IG).
    2. The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.
  1. Blind spot monitor sensor RH
  2. RCTA buzzer (blind spot monitor buzzer)
  3. Harness or connector
C1ABE
  1. Both of the following conditions are met:
    1. Blind spot monitor main switch assembly (multi-function switch) is on with engine switch on (IG).
    2. The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.
  1. Blind spot monitor sensor RH
  2. RCTA buzzer (blind spot monitor buzzer)
  3. Harness or connector

WIRING DIAGRAM

E254403E14

INSPECTION PROCEDURE

NOTICE:
  1. When checking for DTCs, make sure that the blind spot main switch assembly (multi-function switch) is on.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
  1. Disconnect the R44 RCTA buzzer (blind spot monitor buzzer) connector.

  1. Disconnect the R43 blind spot monitor sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R44-2 (BZN) - R43-3 (BUZ)
    Always
    Below 1 Ω
    R44-2 (BZN) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R44-1 (BZP) - Body ground
    Engine switch on (IG)
    11 to 14 V
    R44-1 (BZP) - Body ground
    Engine switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE BLIND SPOT MONITOR BUZZER (RCTA BUZZER)
  1. Replace the RCTA buzzer (blind spot monitor buzzer) with a new or normally functioning one (Click here).


NEXT


4. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)
OK

END (RCTA BUZZER [BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)


← C1ABC Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete (from Aug 2014)C1ABD Short to +B in Buzzer (+ C1ABE) (from Aug 2014) →