B2311 Power Window Motor Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The power window regulator motor is operated by the multiplex network master switch or power window regulator switch. The power window regulator motor assembly has motor, regulator and ECU functions.This DTC is stored when the power window regulator motor has a malfunction, or the ECU built into the regulator motor determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.
- HINT:
- DTC B2311 can be stored in each power window regulator motor (power window ECU).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
- *1: for LHD
- *2: for RHD
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
|
- *1: for LHD
- *2: for RHD
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
Rear power window regulator motor LH |
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2311 |
|
Rear power window regulator motor RH |
INSPECTION PROCEDURE
- NOTICE:
- When a power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
- After any door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
- Close the power window by fully pulling up the multiplex network master switch or power window regulator switch and holding it in the auto up position.
- Open the power window by fully pushing down the switch.
- When a power window regulator motor is reinstalled or replaced, the power window control system must be initialized.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that each door window regulator operates (Click here).
- CAUTION:
- Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
D-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Driver side power window
OFF/UP/DOWN
-
P-Door Motor Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Passenger side power window
OFF/UP/DOWN
-
RL-Door Motor (for 5 Door) Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Rear LH side power window
OFF/UP/DOWN
-
RR-Door Motor (for 5 Door) Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Rear RH side power window
OFF/UP/DOWN
-
- OK:
- Each power window regulator motor operates.
Result Result
Proceed to
OK
A
NG (Front power window LH)
B
NG (Front power window RH)
C
NG (Rear power window LH)*
D
NG (Rear power window RH)*
E
- *: for 5 Door
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. PERFORM INITIALIZATION |
Initialize the power window regulator motor assembly (Click here).
Check that each power window operates normally by opening and closing the window (Click here).
- HINT:
- Each power window operates normally.
| NEXT | |
| 3. CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY |
Check that the power window components are installed correctly.
- OK:
- Power window components are installed correctly.
- HINT:
- If the power window components are installed correctly, the problem has been caused by battery disconnection while the ignition switch was ON, or the motor being overheated.
|
|
||||
| OK | ||
| ||
