2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL FRONT CRANKSHAFT OIL SEAL

  1. A225390E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the oil seal at an angle.
    3. Make sure that the oil seal edge does not protrude from the timing chain case.


2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.

    A225681E01

    Text in Illustration 
    *A
    Cylinder head and cylinder block side
    *B
    Timing chain cover side
    *a
    Clean and degrease
    -
    -

    NOTICE:
    Be sure to clean and degrease the contact surfaces, especially the surfaces indicated in the illustration.

  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket.

  1. A225682E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    Text in Illustration 
    *1
    Seal Diameter
    V100135
    Seal Packing

  1. Apply seal packing to the timing chain cover in a continuous line as shown in the following illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


    A221403E01
    Text in Illustration 
    *a
    Be sure to apply seal packing
    *b
    Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *c
    Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    *d
    Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)
    *e
    Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
    -
    -

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.


    Application Specification:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm (0.177 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Alternate Long and Short Dashed Line Area
    3.5 mm (0.138 in.) or more
    2.0 to 3.0 mm (0.0787 to 0.118 in.)
    Dashed Line Area
    3.5 mm (0.138 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Diagonal Line Area
    6.0 mm (0.236 in.) or more
    5.0 mm (0.197 in.)

  1. A221405E01
    Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the drive rotor and chain cover to the crankshaft.
    Text in Illustration 
    *1
    Drive Rotor Spline
    *2
    Crankshaft

  1. Install the timing chain cover with the 26 bolts, labeled A, B, C and D, and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Standard Bolt:
    Item
    Length
    Bolt A
    25 mm (0.984 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    35 mm (1.38 in.)
    Bolt D
    65 mm (2.56 in.)


    A221406E01
    Text in Illustration 
    *1
    Nut
    -
    -
    *a
    Area 1
    *b
    Area 2
    *c
    Area 3
    *d
    Area 4

    NOTICE:
    Make sure that there is no oil on the bolt threads.

  1. Tighten the bolts in area 1.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

  1. Tighten the bolts in area 2.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

  1. Tighten the bolts in area 3.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts and nuts from top to bottom as shown in the illustration.

  1. Tighten the bolts in area 4.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

    NOTICE:
    1. Do not start the engine for at least 2 hours after installation.
    2. Wipe off any seal packing that seeped out around the surfaces of the oil pan and head cover and make sure that there is no seal packing seeping out around the edges.


3. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.

  1. Install a new 3 O-rings to the timing chain cover.

  1. A222121E01
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.

  1. A223671E01
    Install the oil pan with the 17 bolts (A, B, C, D and E) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    for bolt A, B, C and E, and nut:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for bolt D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Standard Bolt:
    Item
    Length
    Bolt A
    60 mm (2.36 in.)
    Bolt B
    45 mm (1.77 in.)
    Bolt C
    25 mm (0.984 in.)
    Bolt D
    16 mm (0.630 in.)
    Bolt E
    70 mm (2.76 in.)

    Text in Illustration 
    *1
    Nut

    NOTICE:
    Do not start the engine for at least 2 hours after installing.


4. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A273801E01
    Install a new gasket to the oil strainer.
    Text in Illustration 
    *1
    Groove
    *2
    Protrusion

    HINT:
    Align the protrusion of the gasket with the groove of the oil strainer.

  1. Install the oil strainer with the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


5. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A174349E02
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan within 3 minutes after applying seal packing.

  1. A225446
    Install the No. 2 oil pan with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut

    NOTICE:
    1. Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.
    2. Do not start the engine for at least 2 hours after the installation.


6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A223667
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Install 3 new gaskets.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A225447E01
    Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    65 mm (2.56 in.)
    D
    60 mm (2.36 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    NOTICE:
    Do not start the engine for at least 2 hours after installation.


7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.

  1. A223664
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

  1. Install 3 new gaskets.

  1. Install a new gasket to the cylinder head cover.

  1. Install the seal washers to the bolts.

  1. A226494E01
    Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.

    Torque:
    for bolt A and D:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B and C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Standard Bolt:
    Item
    Length
    A
    25 mm (0.984 in.)
    B
    35 mm (1.38 in.)
    C
    70 mm (2.76 in.)
    D
    60 mm (2.36 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Bolt C
    V100138
    Bolt D

    NOTICE:
    Do not start the engine for at least 2 hours after installation.


8. CONNECT FUEL PIPE SUB-ASSEMBLY
  1. Connect the fuel pipe with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


9. INSTALL REAR CYLINDER HEAD COVER
  1. Temporarily install the cover with the 3 bolts.

  1. A224695E01
    Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


10. INSTALL NO. 2 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }


11. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }


12. INSTALL CRANKSHAFT PULLEY

  1. A076309E03
    Using SST, install the crankshaft pulley with the pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }


13. INSTALL OIL FILTER BRACKET
  1. Install the oil filter bracket and a new gasket with the 2 nuts and bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


14. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A226495E01
    Temporarily install the V-ribbed belt tensioner with the 5 bolts.

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

  1. Tighten bolts 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


15. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Separate Type:
    Install the 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Integrated Type:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


16. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A076438E01
    Install the No. 1 idler pulley with the bolt.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    HINT:
    "DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No. 2 idler pulley.


17. INSTALL WATER INLET HOUSING
  1. Install the 3 water by-pass hoses.

  1. Apply soapy water to a new O-ring and install the O-ring to the water outlet pipe.

  1. Install a new O-ring to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Install the water inlet with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 3 water by-pass hoses.


18. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

  1. A223698E01
    Install the water by-pass pipe with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 2 hoses.

    Text in Illustration 
    *a
    Upward
    *b
    Rearward

    HINT:
    The direction of the hose clamp is indicated in the illustration.


19. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A223631E01
    Install a new O-ring to the dipstick guide.
    Text in Illustration 
    *1
    New O-Ring

  1. Apply a light coat of engine oil to the O-ring.

  1. Push the dipstick guide end into the guide hole.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.


20. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.


21. INSTALL NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
  1. Install the No. 2 emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


22. INSTALL EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
  1. Install the emission control valve set with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


23. INSTALL ENGINE ASSEMBLY
  1. Install the engine assembly (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (from Aug 2013) →