2013-2015 Land Cruiser Prado · Service Manual General

SERVICE DATA

Specifications · Vehicles built from Aug 2013

Line Pressure and Shift schedule 
Line pressure (Wheel locked)
AT stall
(Throttle valve fully opened)
D position
1050 to 1200 kPa (10.7 to 12.2 kgf/cm2, 152 to 174 psi)
R position
1300 to 1650 kPa (13.3 to 16.8 kgf/cm2, 189 to 239 psi)
Engine stall revolution
D and R positions
1800 to 2200 rpm
Time lag
N → D position
Less than 1.2 seconds
N → R position
Less than 1.5 seconds
Engine idle speed (A/C OFF)
N position
600 to 700 rpm
Drive plate runout
Maximum
0.30 mm (0.0118 in.)
Shift schedule
(Speeds higher than the fuel cut speed are for reference only)
D position
(Throttle valve fully opened)
1 → 2
54 to 62 km/h (34 to 39 mph)
2 → 3
100 to 112 km/h (62 to 70 mph)
3 → 4
145 to 156 km/h (90 to 97 mph)
D position
(Throttle valve opening 5%)
1 → 2
11 to 15 km/h (7 to 9 mph)
2 → 3
16 to 20 km/h (10 to 12 mph)
3 → 4
44 to 49 km/h (27 to 30 mph)
Manual downshift permissible speed
(Speeds higher than the fuel cut speed are for reference only)
S position
→ 3
160 to 170 km/h (99 to 106 mph)
→ 2
105 to 114 km/h (65 to 71 mph)
→ 1
51 to 56 km/h (32 to 35 mph)
Speed Sensor 
Speed sensor NC0 and SP2
20°C (68°F)
560 to 680 Ω
No. 2 ATF Temperature Sensor 
No. 2 temperature sensor
Always
560 to 680 Ω
No. 1 temperature sensor
Always
79 Ω to 156 kΩ
Shift Solenoid Valve 
SLU and SLT
20°C (68°F)
5.0 to 5.6 Ω
S1 and S2
20°C (68°F)
11 to 15 Ω
Transfer Adaptor Oil Seal 
Standard depth
0 to 1 mm (0 to 0.0394 in.)
Drive Plate 
Maximum runout
0.30 mm (0.0118 in.)
Overdrive Clutch 
Clutch piston return spring free length
Standard
15.8 mm (0.622 in.)
Overdrive direct clutch drum bush inside diameter
Maximum
27.11 mm (1.07 in.)
Flange thickness
Mark 21
3.05 to 3.15 mm (0.120 to 0.124 in.)
Mark 20
3.15 to 3.25 mm (0.124 to 0.128 in.)
Mark 19
3.25 to 3.35 mm (0.128 to 0.132 in.)
Mark 18
3.35 to 3.45 mm (0.132 to 0.136 in.)
Mark 17
3.45 to 3.55 mm (0.136 to 0.140 in.)
Mark 16
3.55 to 3.65 mm (0.140 to 0.144 in.)
Overdrive Planetary Gear Assembly 
Planetary gear bush inside diameter
Maximum
11.2 to 11.221 mm (0.441 to 0.442 in.)
Pinion gear thrust clearance
Standard
0.20 to 0.60 mm (0.00787 to 0.0236 in.)
Maximum
0.65 mm (0.0256 in.)
Overdrive Brake 
Brake piston return spring free length
Standard
17.03 mm (0.671 in.)
Flange thickness
Mark 33
3.25 to 3.35 mm (0.128 to 0.132 in.)
Mark 35
3.45 to 3.55 mm (0.136 to 0.140 in.)
Mark 36
3.55 to 3.65 mm (0.140 to 0.144 in.)
Mark 37
3.65 to 3.75 mm (0.144 to 0.148 in.)
Mark 38
3.75 to 3.85 mm (0.148 to 0.152 in.)
Mark 39
3.85 to 3.95 mm (0.152 to 0.156 in.)
Mark 40
3.95 to 4.05 mm (0.156 to 0.159 in.)
Brake piston return spring free length
Standard
15.72 mm (0.619 in.)
Direct Clutch 
Clutch piston return spring free length
Standard
21.32 mm (0.839 in.)
Clutch drum bush inside diameter
Standard
53.915 to 53.94 mm (2.123 to 2.124 in.)
Maximum
53.99 mm (2.13 in.)
Flange thickness
Mark 53
3.25 to 3.35 mm (0.128 to 0.132 in.)
Mark 54
3.35 to 3.45 mm (0.132 to 0.136 in.)
Mark 55
3.45 to 3.55 mm (0.136 to 0.140 in.)
Mark 56
3.55 to 3.65 mm (0.140 to 0.144 in.)
Mark 57
3.65 to 3.75 mm (0.144 to 0.148 in.)
Mark 58
3.75 to 3.85 mm (0.148 to 0.152 in.)
Forward Clutch 
Clutch piston return spring free length
Standard
19.47 mm (0.767 in.)
Forward clutch input shaft bush inside diameter
Standard
24.0 to 24.026 mm (0.945 to 0.946 in.)
Maximum
24.076 mm (0.948 in.)
Flange thickness
Mark 90
2.95 to 3.05 mm (0.116 to 0.120 in.)
Mark 91
3.15 to 3.25 mm (0.124 to 0.128 in.)
Mark 92
3.35 to 3.45 mm (0.132 to 0.136 in.)
Mark 93
3.55 to 3.65 mm (0.140 to 0.144 in.)
Mark 94
3.75 to 3.85 mm (0.148 to 0.152 in.)
Mark 95
3.95 to 4.05 mm (0.156 to 0.159 in.)
Mark 96
4.15 to 4.25 mm (0.163 to 0.167 in.)
Mark 97
4.35 to 4.45 mm (0.171 to 0.175 in.)
Second Coast Brake 
Piston rod length
w/ Groove mark
78.3 to 78.5 mm (3.08 to 3.09 in.)
w/o Groove mark
79.8 to 80.0 mm (3.14 to 3.15 in.)
Piston stroke
Standard
1.5 to 3.0 mm (0.059 to 0.118 in.)
Front Planetary Gear 
Planetary ring gear bush inside diameter
Standard
24.0 to 24.026 mm (0.945 to 0.946 in.)
Maximum
24.076 mm (0.948 in.)
Planetary sun gear bush inside diameter
Standard
27.00 to 27.026 mm (1.063 to 1.064 in.)
Maximum
27.076 mm (1.07 in.)
Planetary pinion gear thrust clearance
Standard
0.20 to 0.60 mm (0.00787 to 0.0236 in.)
Maximum
0.65 mm (0.0256 in.)
Second Brake 
Piston return spring free length
Standard
16.05 mm (0.632 in.)
Rear Planetary Gear 
Planetary pinion gear thrust clearance
Standard
0.2 to 0.6 mm (0.00787 to 0.0236 in.)
Maximum
0.65 mm (0.0256 in.)
First and Reverse Brake 
Brake piston return spring free length
Standard
18.182 to 18.582 mm (0.716 to 0.732 in.)
Transmission Case 
Transmission case bush inside diameter
Standard
38.113 to 38.138 mm (1.5005 to 1.5014 in.)
Maximum
38.19 mm (1.50 in.)
Output Shaft 
Output shaft end play
Standard
0.30 to 1.04 mm (0.0118 to 0.0409 in.)
Accumulator Spring 
C-0 Inner
Yellow
46.0 mm (1.81 in.)/14.02 mm (0.552 in.)
C-0 Outer
Orange
74.6 mm (2.94 in.)/20.9 mm (0.823 in.)
B-0
Red
63.6 mm (2.50 in.)/16.0 mm (0.630 in.)
C-2 Inner
Pink
42.06 mm (1.66 in.)/14.7 mm (0.579 in.)
C-2 Outer
Blue
768.53 mm (2.70 in.)/20.2 mm (0.795 in.)
B-2
Light green
70.50 mm (2.78 in.) 19.9 mm (0.783 in.)
Oil Pump 
Body clearance
Standard
0.07 to 0.15 mm (0.00276 to 0.00591 in.)
Maximum
0.2 mm (0.00787 in.)
Tip clearance
Standard
0.004 to 0.248 mm (0.000157 to 0.00976 in.)
Maximum
0.3 mm (0.0118 in.)
Side clearance
Standard
0.02 to 0.05 mm (0.000787 to 0.00197 in.)
Maximum
0.1 mm (0.00394 in.)
Driver and driven gear thickness
M
M 11.690 to 11.699 mm (0.4602 to 0.4606 in.)
N
11.700 to 11.709 mm (0.4606 to 0.4610 in.)
P
11.710 to 11.720 mm (0.4610 to 0.4614 in.)
R
11.721 to 11.730 mm (0.4615 to 0.4618 in.)
S
11.731 to 11.740 mm (0.4618 to 0.4622 in.)
Pump body inside diameter
Maximum
38.19 mm (1.50 in.)
Stator shaft inside maximum diameter
Front side
21.58 mm (0.8496 in.
Rear side
27.08 mm (1.0661 in.)
← TORQUE SPECIFICATIONS (from Aug 2013)TORQUE SPECIFICATIONS (from Aug 2013) →