2013-2015 Land Cruiser Prado · Service Manual General

SERVICE DATA

Specifications · Vehicles built from Aug 2013


Camshaft Timing Oil Control Valve:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω


Crankshaft Position Sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω


Engine Coolant Temperature Sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ


Throttle Body:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω


Knock Sensor:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ


Accelerator Pedal:
Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 5.3 V


Air Fuel Ratio Sensor (for Bank 1):
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher


Air Fuel Ratio Sensor (for Bank 2):
Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-)
Always
10 kΩ or higher


Heated Oxygen Sensor (for Bank 1):
Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT1B) - 4 (E2)
Always
10 kΩ or higher


Heated Oxygen Sensor (for Bank 2):
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 4 (E2)
Always
10 kΩ or higher


Circuit Opening Relay:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


No. 1 Integration Relay (IG2):
Tester Connection
Condition
Specified Condition
IG2 fuse
Always
Below 1 Ω
1C-1 - 1A-4
Battery voltage not applied to terminals 1A- 1 and 1A-3
10 kΩ or higher
Battery voltage applied to terminals 1A-1 and 1A-3
Below 1 Ω


No. 1 Integration Relay (EFI):
Tester Connection
Condition
Specified Condition
EFI fuse
Always
Below 1 Ω
1C-1 - 1B-4
Battery voltage not applied to terminals 1B- 2 and 1B-3
10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3
Below 1 Ω


No. 1 Integration Relay (A/F):
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1B-8
Battery voltage not applied to terminals 1B- 4 and 1B-7
10 kΩ or higher
Battery voltage applied to terminals 1B-4 and 1B-7
Below 1 Ω


Air Pump Heater Relay:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Air Injection VSV Relay (AI-VSV):
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω


Main Body ECU (Driver Side Junction Block) for ACC Relay:
Tester Connection
Condition
Specified Condition
2D-17 - 2K-1
Battery voltage not applied to terminals 2A- 48 and 2D-4
10 kΩ or higher
Battery voltage applied to terminals 2A-48 and 2D-4
Below 1 Ω


Main Body ECU (Driver Side Junction Block) for IG1 No. 2 Relay:
Tester Connection
Condition
Specified Condition
2A-31 - 2K-1
Battery voltage not applied to terminals 2A- 52 and 2D-4
10 kΩ or higher
Battery voltage applied to terminals 2A-52 and 2D-4
Below 1 Ω


Spark Plug:
Recommended spark plug
Correct electrode gap for new spark plug
Maximum electrode gap for used spark plug
Standard insulation resistance
SK16HR11
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
1.3 mm (0.0512 in.)
10 MΩ or higher

← HOW TO DETERMINE NUT STRENGTH (from Aug 2013)TORQUE SPECIFICATIONS (from Aug 2013) →