2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
E132743E23
  1. Disconnect the G24 and G25 amplifier connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G25-21 (B) - G25-14 (GND)
    V - W-B
    Battery power source
    Always
    11 to 14 V
    G25-1 (IG+) - G25-14 (GND)
    L - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    G25-14 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    G24-20 (RGND) - Body ground*1
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    G24-24 (+B2) - G24-20 (RGND)*1
    GR - W-B
    Battery power source
    Always
    11 to 14 V

  3. Reconnect the G24 and G25 amplifier connectors.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G25-3 (PTC1) - Body ground*8
    V - Body ground
    PTC NO. 1 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 79°C (175°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    11 to 14 V*10
    G25-4 (PTC3) - Body ground*8
    P - Body ground
    PTC NO. 3 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 73°C (163°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    11 to 14 V*10
    G25-5 (TAM) - G25-13 (SG-2)*9
    V - G
    Cooler thermistor (ambient temperature sensor) signal
    1. Ignition switch ON
    2. Ambient temperature 25°C (77°F)
    1.35 to 1.75 V
    G25-5 (TAM) - G25-13 (SG-2)*9
    V - G
    Cooler thermistor (ambient temperature sensor) signal
    1. Ignition switch ON
    2. Ambient temperature 40°C (104°F)
    0.9 to 1.2 V
    G25-8 (LOCK) - G25-13 (SG-2)*2,*9
    R - G
    A/C compressor lock sensor signal
    1. Engine running
    2. Blower switch LO
    3. A/C switch on
    Pulse generation
    (See waveform 1)
    G25-9 (PRE) - G25-13 (SG-2)*3,*9
    G - G
    Air conditioner pressure sensor signal
    1. Ignition switch ON
    2. Refrigerant pressure normal (below 3.025 MPa [30.9 kgf/cm2, 438.6 psi] and higher than 0.176 MPa [1.8 kgf/cm2, 25.5 psi])
    0.63 to 4.72 V
    G25-9 (PRE) - G25-13 (SG-2)*3,*9
    G - G
    Air conditioner pressure sensor signal
    1. Ignition switch ON
    2. Refrigerant pressure abnormal (below 0.176 MPa [1.8 kgf/cm2, 25.5 psi])
    Below 0.63 V
    G25-9 (PRE) - G25-13 (SG-2)*3,*9
    G - G
    Air conditioner pressure sensor signal
    1. Ignition switch ON
    2. Refrigerant pressure abnormal (higher than 3.025 MPa [30.9 kgf/cm2, 438.6 psi])
    4.72 V or higher
    G25-9 (PRE) - Body ground*4,*9
    G - Body ground
    No. 1 pressure switch signal
    1. Ignition switch ON
    2. Refrigerant pressure normal (below 3.14 MPa [32.0 kgf/cm2, 455 psi] and higher than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    Below 1 V
    G25-9 (PRE) - Body ground*4,*9
    G - Body ground
    No. 1 pressure switch signal
    1. Ignition switch ON
    2. Refrigerant pressure abnormal (below 0.196 MPa [2.0 kgf/cm2, 28 psi] or higher than 3.14 MPa [32.0 kgf/cm2, 455 psi])
    4.69 V or higher
    G25-10 (S5-3) - G25-13 (SG-2)*9
    B - G
    Power supply for air conditioner pressure sensor
    Ignition switch ON
    4.75 to 5.25 V
    G25-15 (COOL) - G25-14 (GND)*5
    V - W-B
    Cooling box assembly operation signal
    1. Engine running
    2. Cooler control switch sub-assembly on
    Below 1 V
    G25-16 (MG+) - G25-14 (GND)*7
    V - W-B
    Viscous with magnetic clutch heater assembly operation signal
    1. Engine running
    2. Power heater switch on
    Below 1 V
    G25-17 (AC1) - G25-14 (GND)*9
    LG - W-B
    Compressor operation signal
    1. Ignition switch ON
    2. A/C switch on
    Below 1 V
    G25-18 (MHTR) - G25-14 (GND)
    G - W-B
    MIR HTR relay signal
    1. Ignition switch ON
    2. Mirror heater switch on
    Below 1 V
    G25-20 (MGC) - G25-14 (GND)*9
    R - W-B
    Magnet clutch assembly operation signal
    1. Ignition switch ON
    2. Blower switch LO
    3. A/C switch on
    Below 1 V
    G25-22 (PTC2) - Body ground*8
    LG - Body ground
    PTC NO. 2 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting MAX HOT
    3. Outside temperature 10°C (50°F) or less
    4. Engine coolant temperature 76°C (169°F) or less
    5. Headlight dimmer switch off
    6. Blower switch on
    11 to 14 V*10
    G25-23 (BLW) - G25-14 (GND)
    L - W-B
    Blower with fan motor sub-assembly control signal
    1. Ignition switch ON
    2. Blower switch LO
    Pulse generation
    (See waveform 2)
    G25-25 (ALT) - G25-14 (GND)*8
    L - W-B
    Generator signal (PTC heater control)
    Engine started
    Pulse generation
    G25-27 (ACT) - G25-14 (GND)*9
    R - W-B
    Compressor operation signal
    1. Ignition switch ON
    2. A/C switch on
    4.75 to 5.25 V
    G25-36 (SWVC) - G25-14 (GND)*6
    W - W-B
    Idle up switch operation signal
    1. Ignition switch ON
    2. Idle up switch on
    Below 1 V
    G25-36 (SWVC) - G25-14 (GND)*7
    W - W-B
    Heater switch assembly operation signal
    1. Ignition switch ON
    2. Heater switch assembly on
    Below 1 V
    G24-1 (RBUS) - G24-21 (RBUG)*1
    LG - L
    BUS IC control signal (for Rear)
    Ignition switch ON
    Pulse generation
    G24-4 (TEC) - G24-19 (SGND)*1
    SB - V
    Rear evaporator temperature sensor signal
    1. Ignition switch ON
    2. Rear evaporator temperature 0°C (32°F)
    2.0 to 2.4 V
    1. Ignition switch ON
    2. Rear evaporator temperature: 15°C (59°F)
    1.4 to 1.8 V
    G24-12 (SWCB) - G25-14 (GND)*5
    LG - W-B
    Cooling box assembly operation signal
    1. Ignition switch ON
    2. A/C switch on
    3. Cooler control switch sub-assembly on
    Below 1 V
    G24-19 (SGND) - Body ground*1
    V - Body ground
    Ground for rear evaporator temperature sensor
    Always
    Below 1 V
    G24-20 (RGND) - Body ground*1
    W-B - Body ground
    Ground for power supply
    Always
    Below 1 V
    G24-22 (BLWH) - G24-20 (RGND)*1
    W - W-B
    Rear blower with fan motor sub-assembly control signal
    1. Ignition switch ON
    2. Rear blower switch on
    Pulse generation
    (See waveform 2)
    G24-23 (RBBU) - G24-21 (RBUG)*1
    P - L
    Power supply for BUS IC (for Rear)
    Always
    11 to 14 V
    z1-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 V
    z1-3 (BUS) - z1-2 (BUS G)
    -
    BUS IC control signal
    Ignition switch ON
    Pulse generation
    z1-4 (B BUS) - z1-2 (BUS G)
    -
    Power supply for BUS IC
    Always
    11 to 14 V
    z1-6 (TEA) - z1-5 (SGA)*9
    -
    No. 1 cooler thermistor signal
    1. Ignition switch ON
    2. Evaporator temperature 0°C (32°F)
    1.7 to 2.1 V
    1. Ignition switch ON
    2. Evaporator temperature 15°C (59°F)
    0.9 to 1.3 V
    1. *1: w/ Rear Air Conditioning System
    2. *2: except 5L-E
    3. *3: for 1KD-FTV or w/ Rear Air Conditioning System
    4. *4: except 1KD-FTV and w/o Rear Air Conditioning System
    5. *5: w/ Refrigerated Cool Box
    6. *6: w/ Idle Up Switch
    7. *7: w/ Viscous Heater
    8. *8: w/ PTC Heater
    9. *9: w/ Cooler

      HINT:
      *10: After the measurement conditions are met, wait 30 seconds before performing measurements. If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.

  5. E116941E01
    Using an oscilloscope, check waveform 1.
    A/C Compressor Lock Sensor Signal 
    Item
    Content
    Terminal No. (Symbol)
    G25-8 (LOCK) - G25-14 (GND)
    Tool Setting
    200 mV/DIV., 10 ms./DIV.
    Condition
    1. Engine running
    2. A/C switch on
    3. Blower switch LO

  6. E103396E12
    Using an oscilloscope, check waveform 2.
    Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    1. G25-23 (BLW) - H46-14 (GND)
    2. G24-22 (BLWH) - G24-20 (RGND)
    Tool Setting
    1 V/DIV., 500 μs/DIV.
    Condition
    1. Ignition switch ON
    2. Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (FOR COOLING BOX) (w/ Refrigerated Cool Box)
E197829
  1. Disconnect the air conditioning amplifier (for cooling box) connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1 (+B) - 4 (GND)
    W-R - W-B
    Battery power source
    Always
    11 to 14 V
    2 (IG+) - 4 (GND)
    GR - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the air conditioning amplifier (for cooling box) connectors.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    5 (SW) - 4 (GND)
    LG-R - W-B
    Cooler control switch sub-assembly operation signal
    1. Engine running
    2. Cooler control switch on
    Below 1 V
    6 (CBI) - 4 (GND)
    L-G - W-B
    Cooler compressor permission signal
    1. Engine running
    2. Cooler control switch sub-assembly on
    Below 1 V
    7 (LED) - 4 (GND)
    L-B - W-B
    Cooling box indicator signal
    1. Engine running
    2. Cooler control switch sub-assembly on
    Below 1 V
    8 (CBT) - 4 (GND)
    BR-Y - W-B
    Air conditioning amplifier assembly request signal
    1. Engine running
    2. Cooler control switch sub-assembly on
    Below 1 V
    9 (BLW) - 4 (GND)
    W - W-B
    No. 1 cooler blower motor sub-assembly operation signal
    1. Engine running
    2. Cooler control switch sub-assembly on
    Below 1 V
    10 (SG) - 4 (GND)
    W-L - W-B
    Ground
    Always
    Below 1 Ω


CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY
E196915E04
  1. Disconnect the G23 panel connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G23-1 (+B) - G23-4 (GND)
    L - W-B
    Battery power source
    Always
    11 to 14 V
    G23-5 (IG) - G23-4 (GND)
    L - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    G23-6 (ACC) - G23-4 (GND)
    P - W-B
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    G23-4 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Air Conditioning System)
E196915E05
  1. Disconnect the T3 control connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T3-5 (IG) - T3-8 (E)
    L - W-B
    IG power supply
    Ignition switch ON
    11 to 14 V
    T3-8 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (from Aug 2013) →