SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Aug 2013
| GENERAL |
The air conditioning system has the following controls.
Control
Outline
Manual Control
The air conditioning amplifier assembly controls the damper positions (air inlet control damper, air mix control damper and mode control damper) and blower speed in accordance with the positions of the switches (temperature control dial, blower dial, mode operation switch and REC/FRS switch).
Air Inlet Control
Drives the recirculation damper servo sub-assembly according to the operation of the REC/FRS switch and moves the dampers to the fresh or recirculation position.
Compressor Control
The air conditioning amplifier assembly compares the A/C pulley speed signals, which are transmitted by the ECM (crankshaft position sensor). When the air conditioning amplifier assembly determines that the A/C pulley is locked, it turns off the magnet clutch assembly.
Defroster Control
Defroster control logic is used to improve defroster performance.
Defroster Fresh Air Mode Switching Control
Defroster fresh air mode switching control changes the system from recirculation air mode to fresh air mode to improve defroster performance.
Rear Defogger Control
When the ignition switch is ON and the rear defogger switch is pushed, the system is activated to keep the defogger heater on for approx. 15 minutes. However, the operating time of the rear defogger can be extended up to approx. 255 minutes when both of the following requirements are met: - Ambient Temperature: -3°C (26.6°F) or less
- Vehicle Speed: 50 km/h (31.1 mph) or more
Diagnosis
A Diagnostic Trouble Code (DTC) is stored in memory when the air conditioning amplifier assembly detects a problem with the air conditioning system.
- Ambient Temperature: -3°C (26.6°F) or less
| MODE POSITION AND DAMPER OPERATION |
Mode Position and Damper Operation
Front Air Conditioning Unit


Function of Main Damper Control Damper
Operation Position
Damper Position
Operation
Air Inlet Control Damper
Fresh
A
Brings in fresh air.
Recirculation
B
Recirculates internal air.
Air Mix Control Damper
MAX COOL to MAX HOT
E - D - C
Varies the mixture of cold air and hot air in order to regulate the temperature continuously from hot to cool.
MAX COOL Damper
MAX COOL
V
Open in the MAX COOL position.
Except MAX COOL
W
Close in all position except MAX COOL position.
MAX HOT Damper
MAX HOT
Y
Open in the MAX HOT position.
Except MAX HOT
X
Closed in all position except MAX HOT position.
Mode Control Damper


Face
F, I, N, T, X
Air blows out of the front center registers, side registers and rear face registers.


Bi-level
G, L, N, T, X
Air blows out of the front center registers, side registers, rear face registers and front and rear footwell register ducts.


Foot
H, M, P, T, W, Y (MAX HOT position)
H, M, O, T, X (Except MAX HOT position)
Air blows out of the front and rear footwell register ducts.
In addition, air blows out slightly from the front defroster, side registers, front center registers and rear face registers.


Foot/Def
H, K, R, T, W, Y (MAX HOT position)
H, M, Q, T, X (Except MAX HOT position)
Defrosts the windshield through the front defroster and side registers while air is also blown out from the front and rear footwell register ducts.
In addition, air blows out slightly from the front center registers and rear face registers.


Def
H, I, S, U, X
Defrosts the windshield through the front defrosters.
Rear Air Conditioning Unit (w/ Rear Air Conditioning System)


Function of Main Damper Control Damper
Operation Position
Damper Position
Operation
Mode Control Damper


Face
A
Air blows out from the rear roof registers.


Bi-level
B
Air blows out from the rear roof registers and rear side registers.


Foot
C
Air blows out from the rear side registers.
Air Mix Control Damper
MAX COLD to MAX HOT Temperature Setting
D, E
Varies the mixture of cold air and hot air in order to regulate the temperature continuously from hot to cold.
| AIR OUTLETS AND AIRFLOW VOLUME |
Air Outlets and Airflow Volume
for Front Registers


Indication
(Mode)
Front Center Register
Side Register
Front Footwell Register
Rear Face Register
Rear Footwell Register
Front Defroster
A
B
C
D
E
F


Face




-


-
-


Bi-level










-


Foot














Foot/Def














Def
-
-
-
-
-


- HINT:
- The size of the circle indicates the proportion of airflow volume.
- The same system is used for LHD and RHD vehicles.
- The size of the circle indicates the proportion of airflow volume.
for Rear Registers (w/ Rear Air Conditioning System)


Indication
(Mode)
Rear Roof Register
Rear Side Register
A
B


Face


-


Bi-level






Foot
-


- HINT:
- The size of the circle ○ indicates the ratio of airflow volume.
| A/C LOCK SENSOR (except 5L-E, w/ Cooler) |
| No. 1 COOLER THERMISTOR (w/ Cooler) |
| BLOWER WITH FAN MOTOR SUB-ASSEMBLY |
| AIR CONDITIONING HARNESS ASSEMBLY (BUS CONNECTOR) |
A BUS connector is used in the wire harness that connects the servo motor to the air conditioning amplifier assembly.


Connector Type
Connected to
*1: Bus connector
Damper servo sub-assembly LH (mode damper servo)
*2: Bus connector
Damper servo sub-assembly RH (air mix damper servo)
*3: Bus connector
Recirculation damper servo sub-assembly
*4: Bus connector
Air conditioning amplifier assembly
*5: Connector
No. 1 cooler thermistor
Each BUS connector has a built-in communication/driver IC which communicates with each servo motor connector, actuates the servo motor, and has a position detection function.


| SERVO MOTOR |
The pulse pattern type servo motor detects the relative position using 2-bit on/off signals.
The forward and reverse revolutions of this motor are detected using two signals, A and B, which output four types of patterns. The air conditioning amplifier assembly counts the number of pulse patterns in order to determine the stopped position.

| QUICK HEATER ASSEMBLY (w/ PTC Heater) |
General
The PTC heater is located above the heater core in the air conditioner unit.
The PTC heater consists of a PTC element, aluminum fins and brass plates. When current is applied to the PTC element, it generates heat to warm the air that passes through the unit.


PTC Heater Operating Conditions
The on/off operation of the PTC heater is controlled by the air conditioning amplifier assembly in accordance with the engine coolant temperature, ambient temperature, engine speed, air mix setting and electrical load (generator power ratio).
For example, the number of operating PTC heaters varies according to engine coolant temperature as shown in the graph below.

| VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater) |
The viscous with magnet clutch heater assembly, which is located on top of the engine, is driven by a drive belt. Pressing the heater switch assembly provided in the instrument panel engages the magnetic clutch, causing the rotor in the viscous with magnet clutch heater assembly to rotate and the silicon oil to mix. The shear heat that is thus generated heats the coolant.
The viscous with magnet clutch heater assembly is controlled in accordance with the engine speed, coolant temperature and ambient temperature. While the power heater is engaged, the engine idling speed is raised to a predetermined value whenever the shift lever is in N or D.
| COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR) |