2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1413 Evaporator Temperature Sensor Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.
DTC Code
DTC Detection Condition
Trouble Area
B1413
An open or short in the No. 1 cooler thermistor circuit.
  1. No. 1 cooler thermistor
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM

E140288E27

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (NO. 1 COOLER THERMISTOR)
  1. Use the Data List to check if the No. 1 cooler thermistor is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Evaporator Fin Thermistor
    No. 1 cooler thermistor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    Open in the circuit: -29.7°C (-21.46°F).
    Short in the circuit: 59.55°C (139.19°F).

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT NO. 1 COOLER THERMISTOR

  1. E178772E07
    Remove the No. 1 cooler thermistor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    -10°C (14°F)
    7.30 to 9.10 kΩ
    -5°C (23°F)
    5.65 to 6.95 kΩ
    0°C (32°F)
    4.40 to 5.35 kΩ
    5°C (41°F)
    3.40 to 4.15 kΩ
    10°C (50°F)
    2.70 to 3.25 kΩ
    15°C (59°F)
    2.14 to 2.58 kΩ
    20°C (68°F)
    1.71 to 2.05 kΩ
    25°C (77°F)
    1.38 to 1.64 kΩ
    30°C (86°F)
    1.11 to 1.32 kΩ

    Text in Illustration 
    *a
    Sensing Portion
    *b
    Resistance
    *c
    Allowable Range
    *d
    Temperature

    NOTICE:
    1. Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (refer to the graph).



NG
REPLACE NO. 1 COOLER THERMISTOR (Click here)
OK


3. INSPECT AIR CONDITIONING HARNESS ASSEMBLY

  1. E178773E11
    Remove the air conditioning harness assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z1-6 (TEA) - 2
    Always
    Below 1 Ω
    z1-5 (SGA) - 1
    Always
    Below 1 Ω
    z1-6 (TEA) - Body ground
    Always
    10 kΩ or higher
    z1-5 (SGA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Cooler Thermistor)
    *b
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)


← B1412 Ambient Temperature Sensor Circuit (from Aug 2014)B1413 Evaporator Temperature Sensor Circuit (from Aug 2014) →