DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Data List.
According to the display on the intelligent tester, read the Data List.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Ignition Switch
Engine switch on (IG) signal / ON or OFF
ON: Engine switch on (IG)
OFF: Engine switch off
-
#Codes
Number of trouble codes / Min: 0, Max: 255
Number of stored DTCs displayed
-
Immobilizer when IG=ON
Engine immobiliser system status when engine switch on (IG) / Set or Unset
SET: Engine immobiliser system set when engine switch on (IG)
UNSET: Engine immobiliser system unset when engine switch on (IG)
-
Immobiliser
Engine immobiliser system status / Set or Unset
Set: Key not in cabin
Unset: Key in cabin
-
Master Key
Master key code signal / Match or No Match
Match: Master key code sent
No Match: Unmatched master key code sent
-
Sub Key
Sub-key (master key) code signal / Match or No Match
Match: Sub-key (master key) code sent
No Match: Unmatched sub-key (master key) code sent
-
BCC Malfunction
Transponder chip signal / OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Abnormal Status
Transponder chip data / OK or NG
OK: Data OK
NG: Data error
-
Different Encrypt Code
Transponder chip signal / OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Different Serial Number
Transponder chip signal / OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Frame Error
Transponder chip signal / OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Response
Transponder chip signal / OK or NG
OK: Correct data sent
NG: Incorrect data sent
-
Wireless Starter Com ID
Wireless starter communication ID / No Regd or Regd
No Regd: Wireless starter communication ID not registered
Regd: Wireless starter communication ID registered
-
Wireless C Code
Wireless C code / No Regd or Regd
No Regd: Wireless C code not registered
Regd: Wireless C code registered
-
ID-BOX Sleep Condition
ID code box condition / Yes or No
Yes: ID code box in sleep condition
No: ID code box not in sleep condition
-
ID-BOX Start Condition
ID code box condition / Yes or No
Yes: ID code box sends wake up signal
No: ID code box does not send wake up signal
-
Engine Start Request
ID code box start request condition / OK or NG
OK: Start request condition signal received (past)
NG: Start request condition signal not received (past)
-
3bit Code Request
3-bit code request condition / OK or NG
OK: 3-bit code request condition signal received (past)
NG: 3-bit code request condition signal not received (past)
S Code Check
S code verification result / OK or NG
OK: Verification confirmed
NG: Verification not confirmed
-
L Code Check
L code verification result / OK or NG
OK: Verification confirmed
NG: Verification not confirmed
-
Unlock Request Receive
Steering unlock command reception status / OK or NG
OK: Steering unlock request received
NG: Steering unlock request not received
-
Lock Request Receive
Steering lock command reception status / OK or NG
OK: Steering lock request received
NG: Steering lock request not received
-
S Code Check (Past)
S code verification result (past) / OK or NG
OK: Verification confirmed (past)
NG: Verification not confirmed (past)
-
L Code Check (Past)
L code verification result (past) / OK or NG
OK: Verification confirmed (past)
NG: Verification not confirmed (past)
-
EFI Code Receive
SFI*1 or ECD*2 code received (when DTC stored) / OK or NG
OK: SFI code received
NG: SFI code not received
-
EFI communication
SFI*1 or ECD*2 communication / OK or NG
OK: SFI*1 or ECD*2 communication normal
NG: SFI*1 or ECD*2 communication abnormal
-
R Code Check
R Code verification result / OK or NG
OK: Verification confirmed
NG: Verification not confirmed
- *1: for 1GR-FE, 2TR-FE
- *2: for 1KD-FTV
- *1: for 1GR-FE, 2TR-FE
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Entry&Start Tester Display
Test Part
Control Range
Diagnostic Note
Immobiliser Indicator
Security indicator light
ON/OFF
The test is possible when the following conditions are met: - The key is in the cabin.
- The engine switch is on (IG).
- The key is in the cabin.