2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REPLACEMENT

Removal / installation · Vehicles built from Aug 2013

CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


1. REMOVE ENGINE UNDER COVER SEAL
  1. Remove the 2 bolts and engine under cover seal.


2. DISCONNECT FRONT BUMPER COVER LOWER

  1. A225444
    Remove the 2 bolts and clip and disconnect the front bumper cover lower.


3. DISCONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A224795
    Remove the 4 bolts and open the No. 1 engine under cover as shown in the illustration.


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


5. REMOVE OIL FILTER ELEMENT

  1. A094910E09
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A222100
    Remove the oil filter drain plug.

  1. A222101E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    HINT:
    Use a container to catch the draining oil.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

  1. A222102
    Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A222103E01
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A153538E03
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.


6. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, the threads and O-ring groove.

  1. A273217E01
    Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element on the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    Do not pinch the O-ring for the cap.

  1. A273218E01
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    *2
    Oil Filler Cap
    *3
    O-Ring
    *4
    Oil Filter Bracket
    *a
    No Gap

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

  1. A222105E01
    Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.


7. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Engine Oil:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
    0W-20
    5W-20
    5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil
    15W-40
    20W-50


    Standard Oil Capacity (w/o Oil Cooler):
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 Imp. qts)
    Dry fill
    6.9 liters (7.3 US qts, 6.1 Imp. qts)


    Standard Oil Capacity (w/ Oil Cooler):
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)


8. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


9. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


10. CONNECT NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A225431
    Install the 4 bolts to close the No. 1 engine under cover.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


11. CONNECT FRONT BUMPER COVER LOWER
  1. Connect the front bumper cover lower with the 2 bolts and clip.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


12. INSTALL ENGINE UNDER COVER SEAL
  1. Install the engine under cover seal with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

← COMPONENTS (from Aug 2013)COMPONENTS (from Aug 2013) →