2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The seat belt buckle switch RH circuit consists of the center airbag sensor and front seat inner belt RH.
DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1655/37
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch RH circuit for 2 seconds.
  2. A front seat inner belt RH malfunction.
  3. A center airbag sensor malfunction.
  1. Harness and connector
  2. Front seat inner belt assembly RH (Seat belt buckle switch RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM

C217039E03

INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK FOR DTC
  1. Turn the ignition switch to ON.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

    OK:
    The connectors are properly connected.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 3 Door)
    B
    OK (for 5 Door)
    C



A
CONNECT CONNECTORS PROPERLY

B
Go to step 8
C


3. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front seat inner belt RH.

  1. C215710E01
    Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
REPLACE HARNESS AND CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C217040E12

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt RH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q26-2 (RBE+) - Body ground
    Ignition switch ON
    Below 1 V
    Q26-1 (RBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q26-2 (RBE+) - R1-11 (RBE+)
    Always
    Below 1 Ω
    Q26-1 (RBE-) - R1-12 (RBE-)
    Always
    Below 1 Ω
    Q26-2 (RBE+) - Body ground
    Always
    1 MΩ or higher
    Q26-1 (RBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE HARNESS AND CONNECTOR
OK


5. CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

  1. C157773E01
    Connect the connectors to the center airbag sensor and front seat inner belt RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)

6. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt RH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


7. CHECK CENTER AIRBAG SENSOR

  1. C157773E01
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

8. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and front seat inner belt RH.

  1. C208245E01
    Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
REPLACE HARNESS AND CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C217041E03

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Front Seat Inner Belt RH)
    *b
    Rear view of wire harness connector
    (to Center Airbag Sensor)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q26-2 (RBE+) - Body ground
    Ignition switch ON
    Below 1 V
    Q26-1 (RBE-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q26-2 (RBE+) - Q1-15 (RBE+)
    Always
    Below 1 Ω
    Q26-1 (RBE-) - Q1-14 (RBE-)
    Always
    Below 1 Ω
    Q26-2 (RBE+) - Body ground
    Always
    1 MΩ or higher
    Q26-1 (RBE-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE HARNESS AND CONNECTOR
OK


10. CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

  1. C171812E03
    Connect the connectors to the center airbag sensor and the front seat inner belt RH.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
Go to step 11
OK

USE SIMULATION METHOD TO CHECK (Click here)

11. REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt RH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


12. CHECK CENTER AIRBAG SENSOR

  1. C171812E03
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1655 is not output.

    HINT:
    Codes other than DTC B1655 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Seat Inner Belt RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)


← B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (from Aug 2014)B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction (from Aug 2014) →