2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B175750E09
    Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise (Down)

    1. If the result is not as specified, replace the front power window regulator motor assembly LH.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counterclockwise


INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

  1. B180611E07
    Apply positive (+) battery voltage to the connector terminal 2 (B).

    NOTICE:
    Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.
    Motor gear rotates counterclockwise (Up)
    1. Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.
    Motor gear rotates clockwise (Down)

    1. If the result is not as specified, replace the front power window regulator motor assembly RH.

    CAUTION:
    Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Clockwise
    *b
    Counterclockwise

← REMOVAL (from Aug 2014)INSTALLATION (Aug 2013 – Jul 2014) →