2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2322 Front Passenger Side Door ECU Communication Stop

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
  1. *1: for LHD
  2. *2: for RHD
DTC Code
DTC Detection Condition
Trouble Area
B2322
No communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Front power window regulator motor assembly RH*1
  2. Front power window regulator motor assembly LH*2
  3. Main body ECU (multiplex network body ECU)
  4. Harness or connector
  1. *1: for LHD
  2. *2: for RHD

WIRING DIAGRAM

C211493E05

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.

HINT:
When communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
  1. *1: for LHD
  2. *2: for RHD


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2322 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR)
  1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (Click here).

  1. Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - J7-9 (LIN)
    Always
    Below 1 Ω
    A-16 (LIN2) or J7-9 (LIN) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    A-16 (LIN2) - K7-9 (LIN)
    Always
    Below 1 Ω
    A-16 (LIN2) or K7-9 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)

  1. C216965E07
    Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    J7-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    K7-1 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    J7-2 (B) - Body ground
    Always
    11 to 14 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    K7-2 (B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*A
for LHD
*B
for RHD
*a
Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
  1. Temporarily replace the front power window regulator motor assembly RH*1 or LH*2 with a new or normally functioning one (Click here).

    1. *1: for LHD
    2. *2: for RHD


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2322 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)


← B2322 Front Passenger Side Door ECU Communication Stop (Aug 2013 – Jul 2014)B2323 Rear Door RH ECU Communication Stop (Aug 2013 – Jul 2014) →