2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Steering Angle Sensor Communication Stop Mode

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
Steering Angle Sensor Communication Stop Mode
Either condition is met:
  1. "Spiral cable (Steering Angle Sensor)" is not displayed on "Bus Check".
  1. "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside spiral cable sub-assembly (steering angle sensor)
  2. Spiral cable sub-assembly (steering angle sensor) branch wire or connector
  3. Spiral cable sub-assembly (steering angle sensor)
  1. For vehicles with a vehicle stability control system (for vacuum brake booster) only.

WIRING DIAGRAM

C198942E80

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (SPIRAL CABLE SUB-ASSEMBLY BRANCH WIRE)

  1. C198943E14
    Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-4 (CANH) - G33-3 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])



NG
REPAIR OR REPLACE SPIRAL CABLE SUB-ASSEMBLY BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)

  1. C198943E13
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G33-2 (ESS) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G33-6 (BAT) - Body ground
    Always
    11 to 14 V
    G33-5 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)


← Gateway ECU Communication Stop Mode (from Aug 2014)Steering Angle Sensor Communication Stop Mode (from Aug 2014) →