2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built from Aug 2013


1. REMOVE ENGINE WIRE

2. DISCONNECT HEATER WATER HOSE ASSEMBLY

  1. A223694E01
    w/o Warmer:
    Disconnect the 2 hoses and remove the heater water hose assembly.
    Text in Illustration 
    *A
    w/o Warmer
    *B
    w/ Warmer

  1. w/ Warmer:
    Disconnect the 3 hoses and remove the heater water hose assembly.


3. REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A225367
    Remove the 3 nuts and emission control valve set.


4. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

  1. A225368
    Remove the 3 nuts and No. 2 emission control valve set.


5. REMOVE IGNITION COIL ASSEMBLY

  1. A224724
    Remove the 6 bolts and 6 ignition coils.


6. REMOVE REAR CYLINDER HEAD COVER

  1. A224695
    Remove the 3 bolts and cover.


7. REMOVE FUEL PIPE SUB-ASSEMBLY

  1. A224750
    Disconnect the 2 fuel pipes (Click here).

  1. Remove the 2 bolts and No. 1 fuel pipe and No. 2 fuel pipe.


8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A223037
    Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.


9. REMOVE FUEL INJECTOR ASSEMBLY

  1. A223038E01
    Remove the 6 fuel injectors from the fuel delivery pipe.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    Fuel Injector

  1. Remove the O-ring and injector vibration insulator from each fuel injector.


10. REMOVE INTAKE MANIFOLD

  1. A221466
    Remove the 4 nuts, 6 bolts and 2 gaskets.


11. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY (w/ Oil Cooler)

  1. A223013
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and water by-pass pipe.


12. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A158544
    Remove the bolt and No. 1 idler pulley.


13. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A223006
    for Cover Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates.

  1. for Cover Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulleys.


14. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A222180
    Remove the 5 bolts and V-ribbed belt tensioner.


15. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A222114
    Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


16. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

  1. A221156
    Remove the 3 bolts and front No. 1 engine mounting bracket LH.


17. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

  1. A221155
    Remove the 4 bolts and front No. 1 engine mounting bracket RH.


18. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.

CAUTION:
Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.

  1. A177669E01
    Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the ring gear from the flywheel.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2013) →