2013-2015 Land Cruiser Prado · Service Manual Drivetrain

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


INSPECT TRANSFER POSITION SWITCH

  1. Check the harness and connector 4 wheel drive control ECU - battery and body ground).

    1. C217417E07
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      G54-3 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

      Text in Illustration 
      *a
      Component with harness connected
      (4 wheel drive control ECU)
      If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the 4 wheel drive control ECU (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G54-4 (GND) - Body ground
      Always
      Below 1 Ω

      If the result is not as specified, repair or replace the harness or connector.

  1. Check the harness and connector (transfer position switch - 4 wheel drive control ECU).

    1. Disconnect the G53 ECU connector.

    2. Disconnect the G18 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      C217432E03

      Standard Resistance:
      for 1GR-FE, 1KD-FTV:
      Tester Connection
      Condition
      Specified Condition
      G18-2 (LO) - G53-13 (LO)
      Always
      Below 1 Ω
      G18-2 (LO) - Body ground
      Always
      100 kΩ or higher
      G18-4 (GND) - Body ground
      Always
      Below 1 Ω
      for 2TR-FE, 5L-E:
      Tester Connection
      Condition
      Specified Condition
      G18-2 (LO) - G53-13 (LO)
      Always
      Below 1 Ω
      G18-2 (LO) - Body ground
      Always
      100 kΩ or higher
      G18-4 (GND) - Body ground
      Always
      Below 1 Ω
      G18-5 (HI) - G53-11 (2-4)
      Always
      Below 1 Ω
      G18-5 (HI) - Body ground
      Always
      100 kΩ or higher

      Text in Illustration 
      *A
      for 2TR-FE, 5L-E
      -
      -
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)
      *b
      Front view of wire harness connector
      (to 4 wheel drive control ECU)
      If the result is not as specified, repair or replace the harness or connector.

  1. Check the transfer position switch.

    1. Turn the ignition switch off.

    2. Connect the G18 switch connector.

    3. Connect the G53 ECU connector.

    4. C217417E14
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for 1GR-FE, 1KD-FTV:
      Tester Connection
      Switch Condition
      Specified Condition
      G53-13 (LO) - Body ground
      Ignition switch ON
      Transfer position switch H4
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch L4
      Below 1.5 V
      for 2TR-FE, 5L-E:
      Tester Connection
      Switch Condition
      Specified Condition
      G53-11 (2-4) - Body ground
      Ignition switch ON
      Transfer position switch H4F
      Below 1.5 V
      Ignition switch ON
      Transfer position switch H4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4L
      10.5 to 14 V
      G53-13 (LO) - Body ground
      Ignition switch ON
      Transfer position switch H4F
      10.5 to 14 V
      Ignition switch ON
      Transfer position switch H4L
      Below 1.5 V
      Ignition switch ON
      Transfer position switch L4L
      Below 1.5 V

      Text in Illustration 
      *A
      for 2TR-FE, 5L-E
      *a
      Component with harness connected
      (4 wheel drive control ECU)
      If the result is not as specified, check the 4 wheel drive control ECU.

  1. Check the 4 wheel drive control ECU.

    1. Disconnect the G18 switch connector.

    2. C217434E03
      Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      for 1GR-FE, 1KD-FTV:
      Tester Connection
      Switch Condition
      Specified Condition
      G18-2 (LO) - Body ground
      Ignition switch ON
      10.5 to 14 V
      for 2TR-FE, 5L-E:
      Tester Connection
      Switch Condition
      Specified Condition
      G18-2 (LO) - Body ground
      Ignition switch ON
      10.5 to 14 V
      G18-5 (HI) - Body ground
      Ignition switch ON
      10.5 to 14 V

      Text in Illustration 
      *A
      for 2TR-FE, 5L-E
      *a
      Front view of wire harness connector
      (to Transfer Position Switch)
      If the result is not as specified, replace the 4 wheel drive control ECU (Click here).
      If the result is normal, replace the transfer position switch (Click here).

← ON-VEHICLE INSPECTION (Aug 2013 – Jul 2014)REMOVAL (from Aug 2013) →